Fock matrix

File:Two-port parameters.PNG

Figure 1: Example two-port network with symbol definitions. Notice the port condition is satisfied: the same current flows into each port as leaves that port.

A two-port network (a kind of four-terminal network or quadripole) is an electrical network (circuit) or device with two pairs of terminals to connect to external circuits. Two terminals constitute a port if the currents applied to them satisfy the essential requirement known as the port condition: the electric current entering one terminal must equal the current emerging from the other terminal on the same port. The ports constitute interfaces where the network connects to other networks, the points where signals are applied or outputs are taken. In a two-port network, often port 1 is considered the input port and port 2 is considered the output port.

The two-port network model is used in mathematical circuit analysis techniques to isolate portions of larger circuits. A two-port network is regarded as a "black box" with its properties specified by a matrix of numbers. This allows the response of the network to signals applied to the ports to be calculated easily, without solving for all the internal voltages and currents in the network. It also allows similar circuits or devices to be compared easily. For example, transistors are often regarded as two-ports, characterized by their h-parameters (see below) which are listed by the manufacturer. Any linear circuit with four terminals can be regarded as a two-port network provided that it does not contain an independent source and satisfies the port conditions.

Examples of circuits analyzed as two-ports are filters, matching networks, transmission lines, transformers, and small-signal models for transistors (such as the hybrid-pi model). The analysis of passive two-port networks is an outgrowth of reciprocity theorems first derived by Lorentz.

In two-port mathematical models, the network is described by a 2 by 2 square matrix of complex numbers. The common models that are used are referred to as z-parameters, y-parameters, h-parameters, g-parameters, and ABCD-parameters, each described individually below. These are all limited to linear networks since an underlying assumption of their derivation is that any given circuit condition is a linear superposition of various short-circuit and open circuit conditions. They are usually expressed in matrix notation, and they establish relations between the variables

$V_1$, voltage across port 1

$I_1$, current into port 1

$V_2$, voltage across port 2

$I_2$, current into port 2

which are shown in figure 1. These current and voltage variables are most useful at low-to-moderate frequencies. At high frequencies (e.g., microwave frequencies), the use of power and energy variables is more appropriate, and the two-port current–voltage approach is replaced by an approach based upon scattering parameters.

General properties

There are certain properties of two-ports that frequently occur in practical networks and can be used to greatly simplify the analysis. These include:

Reciprocal networks

A network is said to be reciprocal if the voltage appearing at port 2 due to a current applied at port 1 is the same as the voltage appearing at port 1 when the same current is applied to port 2. Exchanging voltage and current results in an equivalent definition of reciprocity. In general, a network will be reciprocal if it consists entirely of linear passive components (that is, resistors, capacitors and inductors). In general, it will not be reciprocal if it contains active components such as generators.

Symmetrical networks

A network is symmetrical if its input impedance is equal to its output impedance. Most often, but not necessarily, symmetrical networks are also physically symmetrical. Sometimes also antimetrical networks are of interest. These are networks where the input and output impedances are the duals of each other.

Lossless network

A lossless network is one which contains no resistors or other dissipative elements.

Impedance parameters (z-parameters)

File:Z-equivalent two port.png

Figure 2: z-equivalent two port showing independent variables I₁ and I₂. Although resistors are shown, general impedances can be used instead.

Mining Engineer (Excluding Oil ) Truman from Alma, loves to spend time knotting, largest property developers in singapore developers in singapore and stamp collecting. Recently had a family visit to Urnes Stave Church.

$\left[\begin{array}{c}{V}_1\\ V_2\end{array}\right]=\left[\begin{array}{cc}{z}_{11}& z_{12}\\ z_{21}& z_{22}\end{array}\right]\left[\begin{array}{c}{I}_1\\ I_2\end{array}\right]$

where

$\begin{array}{cc}{z}_{11}& \stackrel{\text{def}}{=}{\frac{V_1}{I_1}|}_{I_2=0}{z}_{12}\stackrel{\text{def}}{=}{\frac{V_1}{I_2}|}_{I_1=0}\\ z_{21}& \stackrel{\text{def}}{=}{\frac{V_2}{I_1}|}_{I_2=0}{z}_{22}\stackrel{\text{def}}{=}{\frac{V_2}{I_2}|}_{I_1=0}\end{array}$

Notice that all the z-parameters have dimensions of ohms.

For reciprocal networks $z_{12}=z_{21}$. For symmetrical networks $z_{11}=z_{22}$. For reciprocal lossless networks all the $z_{\mathrm{m}\mathrm{n}}$ are purely imaginary.

Example: bipolar current mirror with emitter degeneration

File:Current mirror.png

Figure 3: Bipolar current mirror: i₁ is the reference current and i₂ is the output current; lower case symbols indicate these are total currents that include the DC components

File:Smal-signal mirror circuit.png

Figure 4: Small-signal bipolar current mirror: I₁ is the amplitude of the small-signal reference current and I₂ is the amplitude of the small-signal output current

Figure 3 shows a bipolar current mirror with emitter resistors to increase its output resistance. Transistor Q₁ is diode connected, which is to say its collector-base voltage is zero. Figure 4 shows the small-signal circuit equivalent to Figure 3. Transistor Q₁ is represented by its emitter resistance r_E ≈ V_T / I_E (V_T = thermal voltage, I_E = Q-point emitter current), a simplification made possible because the dependent current source in the hybrid-pi model for Q₁ draws the same current as a resistor 1 / g_m connected across r_π. The second transistor Q₂ is represented by its hybrid-pi model. Table 1 below shows the z-parameter expressions that make the z-equivalent circuit of Figure 2 electrically equivalent to the small-signal circuit of Figure 4.

Table 1	Expression	Approximation
$R_{21}={\frac{V_2}{I_1}|}_{I_2=0}$	$-(\beta r_O-R_E)\frac{r_E+R_E}{r_{\pi }+r_E+2R_E}$	$-\beta r_o\frac{r_E+R_E}{r_{\pi }+2R_E}$
$R_{11}={\frac{V_1}{I_1}|}_{I_2=0}$	$(r_E+R_E)\Vert (r_{\pi }+R_E)$Template:Clarify
$R_{22}={\frac{V_2}{I_2}|}_{I_1=0}$	$(1+\beta \frac{R_E}{r_{\pi }+r_E+2R_E})r_O+\frac{r_{\pi }+r_E+R_E}{r_{\pi }+r_E+2R_E}{R}_E$	$(1+\beta \frac{R_E}{r_{\pi }+2R_E})r_O$
$R_{12}={\frac{V_1}{I_2}|}_{I_1=0}$	$R_E\frac{r_E+R_E}{r_{\pi }+r_E+2R_E}$	$R_E\frac{r_E+R_E}{r_{\pi }+2R_E}$

The negative feedback introduced by resistors R_E can be seen in these parameters. For example, when used as an active load in a differential amplifier, I₁ ≈ −I₂, making the output impedance of the mirror approximately R₂₂ -R₂₁ ≈ 2 β r_OR_E /(r_π + 2R_E) compared to only r_O without feedback (that is with R_E = 0 Ω) . At the same time, the impedance on the reference side of the mirror is approximately R₁₁&nbsp− R₁₂ ≈ $\frac{r_{\pi }}{r_{\pi }+2R_E}$$(r_E+R_E)$, only a moderate value, but still larger than r_E with no feedback. In the differential amplifier application, a large output resistance increases the difference-mode gain, a good thing, and a small mirror input resistance is desirable to avoid Miller effect.

Admittance parameters (y-parameters)

File:Y-parameter two-port.PNG

Figure 5: Y-equivalent two port showing independent variables V₁ and V₂. Although resistors are shown, general admittances can be used instead.

Mining Engineer (Excluding Oil ) Truman from Alma, loves to spend time knotting, largest property developers in singapore developers in singapore and stamp collecting. Recently had a family visit to Urnes Stave Church.

$\left[\begin{array}{c}{I}_1\\ I_2\end{array}\right]=\left[\begin{array}{cc}{y}_{11}& y_{12}\\ y_{21}& y_{22}\end{array}\right]\left[\begin{array}{c}{V}_1\\ V_2\end{array}\right]$

where

$\begin{array}{cc}{y}_{11}& \stackrel{\text{def}}{=}{\frac{I_1}{V_1}|}_{V_2=0}{y}_{12}\stackrel{\text{def}}{=}{\frac{I_1}{V_2}|}_{V_1=0}\\ y_{21}& \stackrel{\text{def}}{=}{\frac{I_2}{V_1}|}_{V_2=0}{y}_{22}\stackrel{\text{def}}{=}{\frac{I_2}{V_2}|}_{V_1=0}\end{array}$

Notice that all the Y-parameters have dimensions of siemens.

For reciprocal networks $y_{12}=y_{21}$. For symmetrical networks $y_{11}=y_{22}$. For reciprocal lossless networks all the $y_{\mathrm{m}\mathrm{n}}$ are purely imaginary.

Hybrid parameters (h-parameters) <h-parameters>...</h-parameters>

File:H-equivalent circuit.PNG

Figure 6: H-equivalent two-port showing independent variables I₁ and V₂; h₂₂ is reciprocated to make a resistor

$\left[\begin{array}{c}{V}_1\\ I_2\end{array}\right]=\left[\begin{array}{cc}{h}_{11}& h_{12}\\ h_{21}& h_{22}\end{array}\right]\left[\begin{array}{c}{I}_1\\ V_2\end{array}\right]$

where

$\begin{array}{cc}{h}_{11}& \stackrel{\text{def}}{=}{\frac{V_1}{I_1}|}_{V_2=0}{h}_{12}\stackrel{\text{def}}{=}{\frac{V_1}{V_2}|}_{I_1=0}\\ h_{21}& \stackrel{\text{def}}{=}{\frac{I_2}{I_1}|}_{V_2=0}{h}_{22}\stackrel{\text{def}}{=}{\frac{I_2}{V_2}|}_{I_1=0}\end{array}$

This circuit is often selected when a current amplifier is wanted at the output. The resistors shown in the diagram can be general impedances instead.

Notice that off-diagonal h-parameters are dimensionless, while diagonal members have dimensions the reciprocal of one another.

Example: common-base amplifier

File:Common base hybrid pi current follower.PNG

Figure 7: Common-base amplifier with AC current source I₁ as signal input and unspecified load supporting voltage V₂ and a dependent current I₂.

Note: Tabulated formulas in Table 2 make the h-equivalent circuit of the transistor from Figure 6 agree with its small-signal low-frequency hybrid-pi model in Figure 7. Notation: r_π = base resistance of transistor, r_O = output resistance, and g_m = transconductance. The negative sign for h₂₁ reflects the convention that I₁, I₂ are positive when directed into the two-port. A non-zero value for h₁₂ means the output voltage affects the input voltage, that is, this amplifier is bilateral. If h₁₂ = 0, the amplifier is unilateral.

Table 2	Expression	Approximation
$h_{21}={\frac{I_2}{I_1}|}_{V_2=0}$	$-\frac{\frac{\beta }{\beta +1}{r}_O+r_E}{r_O+r_E}$	$-\frac{\beta }{\beta +1}$
$h_{11}={\frac{V_1}{I_1}|}_{V_2=0}$	$r_E\Vert r_O$	$r_E$
$h_{22}={\frac{I_2}{V_2}|}_{I_1=0}$	$\frac{1}{(\beta +1)(r_O+r_E)}$	$\frac{1}{(\beta +1)r_O}$
$h_{12}={\frac{V_1}{V_2}|}_{I_1=0}$	$\frac{r_E}{r_E+r_O}$	$\frac{r_E}{r_O}\ll 1$

Inverse hybrid parameters (g-parameters) <g-parameters>...</g-parameters>

File:G-equivalent circuit.PNG

Figure 8: G-equivalent two-port showing independent variables V₁ and I₂; g₁₁ is reciprocated to make a resistor

$\left[\begin{array}{c}{I}_1\\ V_2\end{array}\right]=\left[\begin{array}{cc}{g}_{11}& g_{12}\\ g_{21}& g_{22}\end{array}\right]\left[\begin{array}{c}{V}_1\\ I_2\end{array}\right]$

where

$\begin{array}{cc}{g}_{11}& \stackrel{\text{def}}{=}{\frac{I_1}{V_1}|}_{I_2=0}{g}_{12}\stackrel{\text{def}}{=}{\frac{I_1}{I_2}|}_{V_1=0}\\ g_{21}& \stackrel{\text{def}}{=}{\frac{V_2}{V_1}|}_{I_2=0}{g}_{22}\stackrel{\text{def}}{=}{\frac{V_2}{I_2}|}_{V_1=0}\end{array}$

Often this circuit is selected when a voltage amplifier is wanted at the output. Notice that off-diagonal g-parameters are dimensionless, while diagonal members have dimensions the reciprocal of one another. The resistors shown in the diagram can be general impedances instead.

Example: common-base amplifier

File:Common base hybrid pi.PNG

Figure 9: Common-base amplifier with AC voltage source V₁ as signal input and unspecified load delivering current I₂ at a dependent voltage V₂.

Note: Tabulated formulas in Table 3 make the g-equivalent circuit of the transistor from Figure 8 agree with its small-signal low-frequency hybrid-pi model in Figure 9. Notation: r_π = base resistance of transistor, r_O = output resistance, and g_m = transconductance. The negative sign for g₁₂ reflects the convention that I₁, I₂ are positive when directed into the two-port. A non-zero value for g₁₂ means the output current affects the input current, that is, this amplifier is bilateral. If g₁₂ = 0, the amplifier is unilateral.

Table 3	Expression	Approximation
$g_{21}={\frac{V_2}{V_1}|}_{I_2=0}$	$\frac{r_o}{r_{\pi }}+g_m{r}_O+1$	$g_m{r}_O$
$g_{11}={\frac{I_1}{V_1}|}_{I_2=0}$	$\frac{1}{r_{\pi }}$	$\frac{1}{r_{\pi }}$
$g_{22}={\frac{V_2}{I_2}|}_{V_1=0}$	$r_O$	$r_O$
$g_{12}={\frac{I_1}{I_2}|}_{V_1=0}$	$-\frac{\beta +1}{\beta }$	$-1$

ABCD-parameters <ABCD-parameters>...</ABCD-parameters>

The ABCD-parameters are known variously as chain, cascade, or transmission line parameters. There are a number of definitions given for ABCD parameters, the most common is,

$\left[\begin{array}{c}{V}_1\\ I_1\end{array}\right]=\left[\begin{array}{cc}A& B\\ C& D\end{array}\right]\left[\begin{array}{c}{V}_2\\ -I_2\end{array}\right]$

For reciprocal networks $AD-BC=1$. For symmetrical networks $A=D$. For networks which are reciprocal and lossless, A and D are purely real while B and C are purely imaginary.

This representation is preferred because when the parameters are used to represent a cascade of two-ports, the matrices are written in the same order that a network diagram would be drawn, that is, left to right. However, the examples given below are based on a variant definition;

$\left[\begin{array}{c}{V}_2\\ I{\text{'}}_2\end{array}\right]=\left[\begin{array}{cc}{A}^{\prime }& B^{\prime }\\ C^{\prime }& D^{\prime }\end{array}\right]\left[\begin{array}{c}{V}_1\\ I_1\end{array}\right]$

where

$\begin{array}{cccc}{A}^{\prime }& \stackrel{\text{def}}{=}{\frac{V_2}{V_1}|}_{I_1=0}& B^{\prime }& \stackrel{\text{def}}{=}{\frac{V_2}{I_1}|}_{V_1=0}\\ C^{\prime }& \stackrel{\text{def}}{=}{-\frac{I_2}{V_1}|}_{I_1=0}& D^{\prime }& \stackrel{\text{def}}{=}{-\frac{I_2}{I_1}|}_{V_1=0}\end{array}$

The negative signs in the definitions of parameters $C^{\prime }$ and $D^{\prime }$ arise because $I{\text{'}}_2$ is defined with the opposite sense to $I_2$, that is, $I{\text{'}}_2=-I_2$. The reason for adopting this convention is so that the output current of one cascaded stage is equal to the input current of the next. Consequently, the input voltage/current matrix vector can be directly replaced with the matrix equation of the preceding cascaded stage to form a combined $A^{\prime }{B}^{\prime }{C}^{\prime }{D}^{\prime }$ matrix.

The terminology of representing the $ABCD$ parameters as a matrix of elements designated a₁₁ etc. as adopted by some authors and the inverse $A^{\prime }{B}^{\prime }{C}^{\prime }{D}^{\prime }$ parameters as a matrix of elements designated b₁₁ etc. is used here for both brevity and to avoid confusion with circuit elements.

$\begin{array}{cc}[]\left[𝐚\right]& =\left[\begin{array}{cc}{a}_{11}& a_{12}\\ a_{21}& a_{22}\end{array}\right]=\left[\begin{array}{cc}A& B\\ C& D\end{array}\right]\\ \left[𝐛\right]& =\left[\begin{array}{cc}{b}_{11}& b_{12}\\ b_{21}& b_{22}\end{array}\right]=\left[\begin{array}{cc}{A}^{\prime }& B^{\prime }\\ C^{\prime }& D^{\prime }\end{array}\right]\end{array}$

An ABCD matrix has been defined for Telephony four-wire Transmission Systems by P K Webb in British Post Office Research Department Report 630 in 1977.

Table of transmission parameters

The table below lists inverse ABCD parameters for some simple network elements.

Element	[b] matrix	Remarks
Series resistor	$\left[\begin{array}{cc}1& -R\\ 0& 1\end{array}\right]$	R = resistance
Shunt resistor	$\left[\begin{array}{cc}1& 0\\ -\frac{1}{R}& 1\end{array}\right]$	R = resistance
Series conductor	$\left[\begin{array}{cc}1& -\frac{1}{G}\\ 0& 1\end{array}\right]$	G = conductance
Shunt conductor	$\left[\begin{array}{cc}1& 0\\ -G& 1\end{array}\right]$	G = conductance
Series inductor	$\left[\begin{array}{cc}1& -sL\\ 0& 1\end{array}\right]$	L = inductance s = complex angular frequency
Shunt capacitor	$\left[\begin{array}{cc}1& 0\\ -sC& 1\end{array}\right]$	C = capacitance s = complex angular frequency
Transmission Line	$\left[\begin{array}{cc}\cosh \left(\gamma l\right)& Z_0\sinh \left(\gamma l\right)\\ \frac{1}{Z_0}\sinh \left(\gamma l\right)& \cosh \left(\gamma l\right)\end{array}\right]$	Buying, selling and renting HDB and personal residential properties in Singapore are simple and transparent transactions. Although you are not required to engage a real property salesperson (generally often known as a "public listed property developers In singapore agent") to complete these property transactions, chances are you'll think about partaking one if you are not accustomed to the processes concerned. Professional agents are readily available once you need to discover an condominium for hire in singapore In some cases, landlords will take into account you more favourably in case your agent comes to them than for those who tried to method them by yourself. You need to be careful, nevertheless, as you resolve in your agent. Ensure that the agent you are contemplating working with is registered with the IEA – Institute of Estate Brokers. Whereas it might sound a hassle to you, will probably be worth it in the end. The IEA works by an ordinary algorithm and regulations, so you'll protect yourself in opposition to probably going with a rogue agent who prices you more than they should for his or her service in finding you an residence for lease in singapore. There isn't any deal too small. Property agents who are keen to find time for any deal even if the commission is small are the ones you want on your aspect. Additionally they present humbleness and might relate with the typical Singaporean higher. Relentlessly pursuing any deal, calling prospects even without being prompted. Even if they get rejected a hundred times, they still come again for more. These are the property brokers who will find consumers what they need eventually, and who would be the most successful in what they do. 4. Honesty and Integrity This feature is suitable for you who need to get the tax deductions out of your PIC scheme to your property agency firm. It's endorsed that you visit the correct site for filling this tax return software. This utility must be submitted at the very least yearly to report your whole tax and tax return that you're going to receive in the current accounting 12 months. There may be an official website for this tax filling procedure. Filling this tax return software shouldn't be a tough thing to do for all business homeowners in Singapore. A wholly owned subsidiary of SLP Worldwide, SLP Realty houses 900 associates to service SLP's fast rising portfolio of residential tasks. Real estate is a human-centric trade. Apart from offering comprehensive coaching applications for our associates, SLP Realty puts equal emphasis on creating human capabilities and creating sturdy teamwork throughout all ranges of our organisational hierarchy. Worldwide Presence At SLP International, our staff of execs is pushed to make sure our shoppers meet their enterprise and investment targets. Under is an inventory of some notable shoppers from completely different industries and markets, who've entrusted their real estate must the expertise of SLP Worldwide. If you're looking for a real estate or Singapore property agent online, you merely need to belief your instinct. It is because you don't know which agent is sweet and which agent will not be. Carry out research on a number of brokers by looking out the internet. As soon as if you find yourself certain that a selected agent is dependable and trustworthy, you'll be able to choose to utilize his partnerise find you a house in Singapore. More often than not, a property agent is considered to be good if she or he places the contact data on his web site. This is able to imply that the agent does not thoughts you calling them and asking them any questions regarding properties in Singapore. After chatting with them you too can see them of their office after taking an appointment. Another method by way of which you could find out whether the agent is sweet is by checking the feedback, of the shoppers, on the website. There are various individuals would publish their comments on the web site of the Singapore property agent. You can take a look at these feedback and the see whether it will be clever to hire that specific Singapore property agent. You may even get in contact with the developer immediately. Many Singapore property brokers know the developers and you may confirm the goodwill of the agent by asking the developer. = Characteristic impedance Buying, selling and renting HDB and personal residential properties in Singapore are simple and transparent transactions. Although you are not required to engage a real property salesperson (generally often known as a "public listed property developers In singapore agent") to complete these property transactions, chances are you'll think about partaking one if you are not accustomed to the processes concerned. Professional agents are readily available once you need to discover an condominium for hire in singapore In some cases, landlords will take into account you more favourably in case your agent comes to them than for those who tried to method them by yourself. You need to be careful, nevertheless, as you resolve in your agent. Ensure that the agent you are contemplating working with is registered with the IEA – Institute of Estate Brokers. Whereas it might sound a hassle to you, will probably be worth it in the end. The IEA works by an ordinary algorithm and regulations, so you'll protect yourself in opposition to probably going with a rogue agent who prices you more than they should for his or her service in finding you an residence for lease in singapore. There isn't any deal too small. Property agents who are keen to find time for any deal even if the commission is small are the ones you want on your aspect. Additionally they present humbleness and might relate with the typical Singaporean higher. Relentlessly pursuing any deal, calling prospects even without being prompted. Even if they get rejected a hundred times, they still come again for more. These are the property brokers who will find consumers what they need eventually, and who would be the most successful in what they do. 4. Honesty and Integrity This feature is suitable for you who need to get the tax deductions out of your PIC scheme to your property agency firm. It's endorsed that you visit the correct site for filling this tax return software. This utility must be submitted at the very least yearly to report your whole tax and tax return that you're going to receive in the current accounting 12 months. There may be an official website for this tax filling procedure. Filling this tax return software shouldn't be a tough thing to do for all business homeowners in Singapore. A wholly owned subsidiary of SLP Worldwide, SLP Realty houses 900 associates to service SLP's fast rising portfolio of residential tasks. Real estate is a human-centric trade. Apart from offering comprehensive coaching applications for our associates, SLP Realty puts equal emphasis on creating human capabilities and creating sturdy teamwork throughout all ranges of our organisational hierarchy. Worldwide Presence At SLP International, our staff of execs is pushed to make sure our shoppers meet their enterprise and investment targets. Under is an inventory of some notable shoppers from completely different industries and markets, who've entrusted their real estate must the expertise of SLP Worldwide. If you're looking for a real estate or Singapore property agent online, you merely need to belief your instinct. It is because you don't know which agent is sweet and which agent will not be. Carry out research on a number of brokers by looking out the internet. As soon as if you find yourself certain that a selected agent is dependable and trustworthy, you'll be able to choose to utilize his partnerise find you a house in Singapore. More often than not, a property agent is considered to be good if she or he places the contact data on his web site. This is able to imply that the agent does not thoughts you calling them and asking them any questions regarding properties in Singapore. After chatting with them you too can see them of their office after taking an appointment. Another method by way of which you could find out whether the agent is sweet is by checking the feedback, of the shoppers, on the website. There are various individuals would publish their comments on the web site of the Singapore property agent. You can take a look at these feedback and the see whether it will be clever to hire that specific Singapore property agent. You may even get in contact with the developer immediately. Many Singapore property brokers know the developers and you may confirm the goodwill of the agent by asking the developer. = Propagation constant Buying, selling and renting HDB and personal residential properties in Singapore are simple and transparent transactions. Although you are not required to engage a real property salesperson (generally often known as a "public listed property developers In singapore agent") to complete these property transactions, chances are you'll think about partaking one if you are not accustomed to the processes concerned. Professional agents are readily available once you need to discover an condominium for hire in singapore In some cases, landlords will take into account you more favourably in case your agent comes to them than for those who tried to method them by yourself. You need to be careful, nevertheless, as you resolve in your agent. Ensure that the agent you are contemplating working with is registered with the IEA – Institute of Estate Brokers. Whereas it might sound a hassle to you, will probably be worth it in the end. The IEA works by an ordinary algorithm and regulations, so you'll protect yourself in opposition to probably going with a rogue agent who prices you more than they should for his or her service in finding you an residence for lease in singapore. There isn't any deal too small. Property agents who are keen to find time for any deal even if the commission is small are the ones you want on your aspect. Additionally they present humbleness and might relate with the typical Singaporean higher. Relentlessly pursuing any deal, calling prospects even without being prompted. Even if they get rejected a hundred times, they still come again for more. These are the property brokers who will find consumers what they need eventually, and who would be the most successful in what they do. 4. Honesty and Integrity This feature is suitable for you who need to get the tax deductions out of your PIC scheme to your property agency firm. It's endorsed that you visit the correct site for filling this tax return software. This utility must be submitted at the very least yearly to report your whole tax and tax return that you're going to receive in the current accounting 12 months. There may be an official website for this tax filling procedure. Filling this tax return software shouldn't be a tough thing to do for all business homeowners in Singapore. A wholly owned subsidiary of SLP Worldwide, SLP Realty houses 900 associates to service SLP's fast rising portfolio of residential tasks. Real estate is a human-centric trade. Apart from offering comprehensive coaching applications for our associates, SLP Realty puts equal emphasis on creating human capabilities and creating sturdy teamwork throughout all ranges of our organisational hierarchy. Worldwide Presence At SLP International, our staff of execs is pushed to make sure our shoppers meet their enterprise and investment targets. Under is an inventory of some notable shoppers from completely different industries and markets, who've entrusted their real estate must the expertise of SLP Worldwide. If you're looking for a real estate or Singapore property agent online, you merely need to belief your instinct. It is because you don't know which agent is sweet and which agent will not be. Carry out research on a number of brokers by looking out the internet. As soon as if you find yourself certain that a selected agent is dependable and trustworthy, you'll be able to choose to utilize his partnerise find you a house in Singapore. More often than not, a property agent is considered to be good if she or he places the contact data on his web site. This is able to imply that the agent does not thoughts you calling them and asking them any questions regarding properties in Singapore. After chatting with them you too can see them of their office after taking an appointment. Another method by way of which you could find out whether the agent is sweet is by checking the feedback, of the shoppers, on the website. There are various individuals would publish their comments on the web site of the Singapore property agent. You can take a look at these feedback and the see whether it will be clever to hire that specific Singapore property agent. You may even get in contact with the developer immediately. Many Singapore property brokers know the developers and you may confirm the goodwill of the agent by asking the developer. = Length of transmission line (m)

Scattering parameters (S-parameters)

Mining Engineer (Excluding Oil ) Truman from Alma, loves to spend time knotting, largest property developers in singapore developers in singapore and stamp collecting. Recently had a family visit to Urnes Stave Church.

File:Two-port S-parameters.svg

Fig. 17. Terminology of waves used in S-parameter definition.

The previous parameters are all defined in terms of voltages and currents at ports. S-parameters are different, and are defined in terms of incident and reflected waves at ports. S-parameters are used primarily at UHF and microwave frequencies where it becomes difficult to measure voltages and currents directly. On the other hand, incident and reflected power are easy to measure using directional couplers. The definition is,

$\left[\begin{array}{c}{b}_1\\ b_2\end{array}\right]=\left[\begin{array}{cc}{S}_{11}& S_{12}\\ S_{21}& S_{22}\end{array}\right]\left[\begin{array}{c}{a}_1\\ a_2\end{array}\right]$

where the $a_k$ are the incident waves and the $b_k$ are the reflected waves at port k. It is conventional to define the $a_k$ and $b_k$ in terms of the square root of power. Consequently, there is a relationship with the wave voltages (see main article for details).

For reciprocal networks $S_{12}=S_{21}$. For symmetrical networks $S_{11}=S_{22}$. For antimetrical networks $S_{11}=-S_{22}$. For lossless reciprocal networks $|S_{11}|=|S_{22}|$ and $|S_{11}{|}^2+|S_{12}{|}^2=1$.

Scattering transfer parameters (T-parameters)

DTZ's public sale group in Singapore auctions all forms of residential, workplace and retail properties, outlets, homes, lodges, boarding homes, industrial buildings and development websites. Auctions are at present held as soon as a month.

We will not only get you a property at a rock-backside price but also in an space that you've got longed for. You simply must chill out back after giving us the accountability. We will assure you 100% satisfaction. Since we now have been working in the Singapore actual property market for a very long time, we know the place you may get the best property at the right price. You will also be extremely benefited by choosing us, as we may even let you know about the precise time to invest in the Singapore actual property market.

The Hexacube is offering new ec launch singapore business property for sale Singapore investors want to contemplate. Residents of the realm will likely appreciate that they'll customize the business area that they wish to purchase as properly. This venture represents one of the crucial expansive buildings offered in Singapore up to now. Many investors will possible want to try how they will customise the property that they do determine to buy by means of here. This location has offered folks the prospect that they should understand extra about how this course of can work as well.

Singapore has been beckoning to traders ever since the value of properties in Singapore started sky rocketing just a few years again. Many businesses have their places of work in Singapore and prefer to own their own workplace area within the country once they decide to have a everlasting office. Rentals in Singapore in the corporate sector can make sense for some time until a business has discovered a agency footing. Finding Commercial Property Singapore takes a variety of time and effort but might be very rewarding in the long term.

is changing into a rising pattern among Singaporeans as the standard of living is increasing over time and more Singaporeans have abundance of capital to invest on properties. Investing in the personal properties in Singapore I would like to applaud you for arising with such a book which covers the secrets and techniques and tips of among the profitable Singapore property buyers. I believe many novice investors will profit quite a bit from studying and making use of some of the tips shared by the gurus." – Woo Chee Hoe Special bonus for consumers of Secrets of Singapore Property Gurus Actually, I can't consider one other resource on the market that teaches you all the points above about Singapore property at such a low value. Can you? Condominium For Sale (D09) – Yong An Park For Lease

In 12 months 2013, c ommercial retails, shoebox residences and mass market properties continued to be the celebrities of the property market. Models are snapped up in report time and at document breaking prices. Builders are having fun with overwhelming demand and patrons need more. We feel that these segments of the property market are booming is a repercussion of the property cooling measures no.6 and no. 7. With additional buyer's stamp responsibility imposed on residential properties, buyers change their focus to commercial and industrial properties. I imagine every property purchasers need their property funding to understand in value. Scattering transfer parameters, like scattering parameters, are defined in terms of incident and reflected waves. The difference is that T-parameters relate the waves at port 1 to the waves at port 2 whereas S-parameters relate the reflected waves to the incident waves. In this respect T-parameters fill the same role as ABCD parameters and allow the T-parameters of cascaded networks to be calculated by matrix multiplication of the component networks. T-parameters, like ABCD parameters, can also be called transmission parameters. The definition is,

$\left[\begin{array}{c}{a}_1\\ b_1\end{array}\right]=\left[\begin{array}{cc}{T}_{11}& T_{12}\\ T_{21}& T_{22}\end{array}\right]\left[\begin{array}{c}{b}_2\\ a_2\end{array}\right]$

T-parameters are not so easy to measure directly unlike S-parameters. However, S-parameters are easily converted to T-parameters, see main article for details.

Combinations of two-port networks

When two or more two-port networks are connected, the two-port parameters of the combined network can be found by performing matrix algebra on the matrices of parameters for the component two-ports. The matrix operation can be made particularly simple with an appropriate choice of two-port parameters to match the form of connection of the two-ports. For instance, the z-parameters are best for series connected ports.

The combination rules need to be applied with care. Some connections (when dissimilar potentials are joined) result in the port condition being invalidated and the combination rule will no longer apply. This difficulty can be overcome by placing 1:1 ideal transformers on the outputs of the problem two-ports. This does not change the parameters of the two-ports, but does ensure that they will continue to meet the port condition when interconnected. An example of this problem is shown for series-series connections in figures 11 and 12 below.

Series-series connection

File:Two-port series-series.svg

Fig. 10. Two two-port networks with input ports connected in series and output ports connected in series.

When two-ports are connected in a series-series configuration as shown in figure 10, the best choice of two-port parameter is the z-parameters. The z-parameters of the combined network are found by matrix addition of the two individual z-parameter matrices.

$[𝐳]=[𝐳{]}_1+[𝐳{]}_2$

File:Two-port series-series improper.svg

Fig. 11. Example of an improper connection of two-ports. R₁ of the lower two-port has been by-passed by a short circuit.

File:Two-port series-series proper.svg

Fig. 12. Use of ideal transformers to restore the port condition to interconnected networks.

As mentioned above, there are some networks which will not yield directly to this analysis. A simple example is a two-port consisting of a L-network of resistors R₁ and R₂. The z-parameters for this network are;

$[𝐳{]}_1=\left[\begin{array}{cc}{R}_1+R_2& R_2\\ R_2& R_2\end{array}\right]$

Figure 11 shows two identical such networks connected in series-series. The total z-parameters predicted by matrix addition are;

$[𝐳]=[𝐳{]}_1+[𝐳{]}_2=2[𝐳{]}_1=\left[\begin{array}{cc}2R_1+2R_2& 2R_2\\ 2R_2& 2R_2\end{array}\right]$

However, direct analysis of the combined circuit shows that,

$[𝐳]=\left[\begin{array}{cc}{R}_1+2R_2& 2R_2\\ 2R_2& 2R_2\end{array}\right]$

The discrepancy is explained by observing that R₁ of the lower two-port has been by-passed by the short-circuit between two terminals of the output ports. This results in no current flowing through one terminal in each of the input ports of the two individual networks. Consequently, the port condition is broken for both the input ports of the original networks since current is still able to flow into the other terminal. This problem can be resolved by inserting an ideal transformer in the output port of at least one of the two-port networks. While this is a common text-book approach to presenting the theory of two-ports, the practicality of using transformers is a matter to be decided for each individual design.

Parallel-parallel connection

File:Two-port parallel-parallel.svg

Fig. 13. Two two-port networks with input ports connected in parallel and output ports connected in parallel.

When two-ports are connected in a parallel-parallel configuration as shown in figure 13, the best choice of two-port parameter is the y-parameters. The y-parameters of the combined network are found by matrix addition of the two individual y-parameter matrices.

$[𝐲]=[𝐲{]}_1+[𝐲{]}_2$

Series-parallel connection

File:Two-port series-parallel.svg

Fig. 14. Two two-port networks with input ports connected in series and output ports connected in parallel.

When two-ports are connected in a series-parallel configuration as shown in figure 14, the best choice of two-port parameter is the h-parameters. The h-parameters of the combined network are found by matrix addition of the two individual h-parameter matrices.

$[𝐡]=[𝐡{]}_1+[𝐡{]}_2$

Parallel-series connection

File:Two-port parallel-series.svg

Fig. 15. Two two-port networks with input ports connected in parallel and output ports connected in series.

When two-ports are connected in a parallel-series configuration as shown in figure 15, the best choice of two-port parameter is the g-parameters. The g-parameters of the combined network are found by matrix addition of the two individual g-parameter matrices.

$[𝐠]=[𝐠{]}_1+[𝐠{]}_2$

Cascade connection

File:Two-port cascade.svg

Fig. 16. Two two-port networks with the first's output port connected to the second's input port

When two-ports are connected with the output port of the first connected to the input port of the second (a cascade connection) as shown in figure 16, the best choice of two-port parameter is the ABCD-parameters. The a-parameters of the combined network are found by matrix multiplication of the two individual a-parameter matrices.

$[𝐚]=[𝐚{]}_1\cdot [𝐚{]}_2$

A chain of n two-ports may be combined by matrix multiplication of the n matrices. To combine a cascade of b-parameter matrices, they are again multiplied, but the multiplication must be carried out in reverse order, so that;

$[𝐛]=[𝐛{]}_2\cdot [𝐛{]}_1$

Example

Suppose we have a two-port network consisting of a series resistor R followed by a shunt capacitor C. We can model the entire network as a cascade of two simpler networks:

$\begin{array}{cc}[]{\left[𝐛\right]}_1& =\left[\begin{array}{cc}1& -R\\ 0& 1\end{array}\right]\\ {\left[𝐛\right]}_2& =\left[\begin{array}{cc}1& 0\\ -sC& 1\end{array}\right]\end{array}$

The transmission matrix for the entire network $[𝐛]$ is simply the matrix multiplication of the transmission matrices for the two network elements:

$\begin{array}{cc}[][𝐛]& =[𝐛{]}_2\cdot [𝐛{]}_1\\ & =\left[\begin{array}{cc}1& 0\\ -sC& 1\end{array}\right]\left[\begin{array}{cc}1& -R\\ 0& 1\end{array}\right]\\ & =\left[\begin{array}{cc}1& -R\\ -sC& 1+sCR\end{array}\right]\end{array}$

Thus:

$\left[\begin{array}{c}{V}_2\\ I{\text{'}}_2\end{array}\right]=\left[\begin{array}{cc}1& -R\\ -sC& 1+sCR\end{array}\right]\left[\begin{array}{c}{V}_1\\ I_1\end{array}\right]$

Interrelation of parameters

	$\mathbf{[}𝐳\mathbf{]}$	$\mathbf{[}𝐲\mathbf{]}$	$\mathbf{[}𝐡\mathbf{]}$	$\mathbf{[}𝐠\mathbf{]}$	$\mathbf{[}𝐚\mathbf{]}$	$\mathbf{[}𝐛\mathbf{]}$
$\mathbf{[}𝐳\mathbf{]}$	$\left[\begin{array}{cc}{z}_{11}& z_{12}\\ z_{21}& z_{22}\end{array}\right]$	$\left[\begin{array}{cc}\frac{y_{22}}{\Delta \mathbf{[}𝐲\mathbf{]}}& \frac{-y_{12}}{\Delta \mathbf{]}𝐲\mathbf{]}}\\ \frac{-y_{21}}{\Delta \mathbf{[}𝐲\mathbf{]}}& \frac{y_{11}}{\Delta \mathbf{[}𝐲\mathbf{]}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{\Delta \mathbf{[}𝐡\mathbf{]}}{h_{22}}& \frac{h_{12}}{h_{22}}\\ \frac{-h_{21}}{h_{22}}& \frac{1}{h_{22}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{1}{g_{11}}& \frac{-g_{12}}{g_{11}}\\ \frac{g_{21}}{g_{11}}& \frac{\Delta \mathbf{[}𝐠\mathbf{]}}{g_{11}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{a_{11}}{a_{21}}& \frac{\Delta \mathbf{[}𝐚\mathbf{]}}{a_{21}}\\ \frac{1}{a_{21}}& \frac{a_{22}}{a_{21}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-b_{22}}{b_{21}}& \frac{-1}{b_{21}}\\ \frac{-\Delta \mathbf{[}𝐛\mathbf{]}}{b_{21}}& \frac{-b_{11}}{b_{21}}\end{array}\right]$
$\mathbf{[}𝐲\mathbf{]}$	$\left[\begin{array}{cc}\frac{z_{22}}{\Delta \mathbf{[}𝐳\mathbf{]}}& \frac{-z_{12}}{\Delta \mathbf{[}𝐳\mathbf{]}}\\ \frac{-z_{21}}{\Delta \mathbf{[}𝐳\mathbf{]}}& \frac{z_{11}}{\Delta 𝐳}\end{array}\right]$	$\left[\begin{array}{cc}{y}_{11}& y_{12}\\ y_{21}& y_{22}\end{array}\right]$	$\left[\begin{array}{cc}\frac{1}{h_{11}}& \frac{-h_{12}}{h_{11}}\\ \frac{h_{21}}{h_{11}}& \frac{\Delta \mathbf{[}𝐡\mathbf{]}}{h_{11}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{\Delta \mathbf{[}𝐠\mathbf{]}}{g_{22}}& \frac{g_{12}}{g_{22}}\\ \frac{-g_{21}}{g_{22}}& \frac{1}{g_{22}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{a_{22}}{a_{12}}& \frac{-\Delta \mathbf{[}𝐚\mathbf{]}}{a_{12}}\\ \frac{-1}{a_{12}}& \frac{a_{11}}{a_{12}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-b_{11}}{b_{12}}& \frac{1}{b_{12}}\\ \frac{\Delta \mathbf{[}𝐛\mathbf{]}}{b_{12}}& \frac{-b_{22}}{b_{12}}\end{array}\right]$
$\mathbf{[}𝐡\mathbf{]}$	$\left[\begin{array}{cc}\frac{\Delta \mathbf{[}𝐳\mathbf{]}}{z_{22}}& \frac{z_{12}}{z_{22}}\\ \frac{-z_{21}}{z_{22}}& \frac{1}{z_{22}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{1}{y_{11}}& \frac{-y_{12}}{Y_{11}}\\ \frac{y_{21}}{y_{11}}& \frac{\Delta \mathbf{[}𝐲\mathbf{]}}{y_{11}}\end{array}\right]$	$\left[\begin{array}{cc}{h}_{11}& h_{12}\\ h_{21}& h_{22}\end{array}\right]$	$\left[\begin{array}{cc}\frac{g_{22}}{\Delta \mathbf{[}𝐠\mathbf{]}}& \frac{-g_{12}}{\Delta \mathbf{[}𝐠\mathbf{]}}\\ \frac{-g_{21}}{\Delta \mathbf{[}𝐠\mathbf{]}}& \frac{g_{11}}{\Delta \mathbf{[}𝐠\mathbf{]}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{a_{12}}{a_{22}}& \frac{\Delta \mathbf{[}𝐚\mathbf{]}}{a_{22}}\\ \frac{-1}{a_{22}}& \frac{a_{21}}{a_{22}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-b_{12}}{b_{11}}& \frac{1}{b_{11}}\\ \frac{-\Delta \mathbf{[}𝐛\mathbf{]}}{b_{11}}& \frac{-b_{21}}{b_{11}}\end{array}\right]$
$\mathbf{[}𝐠\mathbf{]}$	$\left[\begin{array}{cc}\frac{1}{z_{11}}& \frac{-z_{12}}{z_{11}}\\ \frac{z_{21}}{z_{11}}& \frac{\Delta \mathbf{[}𝐳\mathbf{]}}{z_{11}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{\Delta \mathbf{[}𝐲\mathbf{]}}{y_{22}}& \frac{y_{12}}{y_{22}}\\ \frac{-y_{21}}{y_{22}}& \frac{1}{y_{22}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{h_{22}}{\Delta \mathbf{[}𝐡\mathbf{]}}& \frac{-h_{12}}{\Delta \mathbf{[}𝐡\mathbf{]}}\\ \frac{-h_{21}}{\Delta \mathbf{[}𝐡\mathbf{]}}& \frac{h_{11}}{\Delta \mathbf{[}𝐡\mathbf{]}}\end{array}\right]$	$\left[\begin{array}{cc}{g}_{11}& g_{12}\\ g_{21}& g_{22}\end{array}\right]$	$\left[\begin{array}{cc}\frac{a_{21}}{a_{11}}& \frac{-\Delta \mathbf{[}𝐚\mathbf{]}}{a_{11}}\\ \frac{1}{a_{11}}& \frac{a_{12}}{a_{11}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-b_{21}}{b_{22}}& \frac{-1}{b_{22}}\\ \frac{\Delta \mathbf{[}𝐛\mathbf{]}}{b_{22}}& \frac{-b_{12}}{b_{22}}\end{array}\right]$
$\mathbf{[}𝐚\mathbf{]}$	$\left[\begin{array}{cc}\frac{z_{11}}{z_{21}}& \frac{\Delta \mathbf{[}𝐳\mathbf{]}}{z_{21}}\\ \frac{1}{z_{21}}& \frac{z_{22}}{z_{21}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-y_{22}}{y_{21}}& \frac{-1}{y_{21}}\\ \frac{-\Delta \mathbf{[}𝐲\mathbf{]}}{y_{21}}& \frac{-y_{11}}{y_{21}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-\Delta \mathbf{[}𝐡\mathbf{]}}{h_{21}}& \frac{-h_{11}}{h_{21}}\\ \frac{-h_{22}}{h_{21}}& \frac{-1}{h_{21}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{1}{g_{21}}& \frac{g_{22}}{g_{21}}\\ \frac{g_{11}}{g_{21}}& \frac{\Delta \mathbf{[}𝐠\mathbf{]}}{g_{21}}\end{array}\right]$	$\left[\begin{array}{cc}{a}_{11}& a_{12}\\ a_{21}& a_{22}\end{array}\right]$	$\left[\begin{array}{cc}\frac{b_{22}}{\Delta \mathbf{[}𝐛\mathbf{]}}& \frac{-b_{12}}{\Delta \mathbf{[}𝐛\mathbf{]}}\\ \frac{-b_{21}}{\Delta \mathbf{[}𝐛\mathbf{]}}& \frac{b_{11}}{\Delta \mathbf{[}𝐛\mathbf{]}}\end{array}\right]$
$\mathbf{[}𝐛\mathbf{]}$	$\left[\begin{array}{cc}\frac{z_{22}}{z_{12}}& \frac{-\Delta \mathbf{[}𝐳\mathbf{]}}{z_{12}}\\ \frac{-1}{z_{12}}& \frac{z_{11}}{z_{12}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-y_{11}}{y_{12}}& \frac{1}{y_{12}}\\ \frac{\Delta \mathbf{[}𝐲\mathbf{]}}{y_{12}}& \frac{-y_{22}}{y_{12}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{1}{h_{12}}& \frac{-h_{11}}{h_{12}}\\ \frac{-h_{22}}{h_{12}}& \frac{\Delta \mathbf{[}𝐡\mathbf{]}}{h_{12}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{-\Delta \mathbf{[}𝐠\mathbf{]}}{g_{12}}& \frac{g_{22}}{g_{12}}\\ \frac{g_{11}}{g_{12}}& \frac{-1}{g_{12}}\end{array}\right]$	$\left[\begin{array}{cc}\frac{a_{22}}{\Delta \mathbf{[}𝐚\mathbf{]}}& \frac{-a_{12}}{\Delta \mathbf{[}𝐚\mathbf{]}}\\ \frac{-a_{21}}{\Delta \mathbf{[}𝐚\mathbf{]}}& \frac{a_{11}}{\Delta \mathbf{[}𝐚\mathbf{]}}\end{array}\right]$	$\left[\begin{array}{cc}{b}_{11}& b_{12}\\ b_{21}& b_{22}\end{array}\right]$

Where $\Delta \mathbf{[}𝐱\mathbf{]}$ is the determinant of [x].

Certain pairs of matrices have a particularly simple relationship. The admittance parameters are the matrix inverse of the impedance parameters, the inverse hybrid parameters are the matrix inverse of the hybrid parameters, and the [b] form of the ABCD-parameters is the matrix inverse of the [a] form. That is,

$[𝐲]=[𝐳{]}^{-1}$

$[𝐠]=[𝐡{]}^{-1}$

$[𝐛]=[𝐚{]}^{-1}$

Networks with more than two ports

While two port networks are very common (e.g., amplifiers and filters), other electrical networks such as directional couplers and circulators have more than 2 ports. The following representations are also applicable to networks with an arbitrary number of ports:

• Admittance (y) parameters
• Impedance (z) parameters
• Scattering (S) parameters

For example three-port impedance parameters result in the following relationship:

$\left[\begin{array}{c}{V}_1\\ V_2\\ V_3\end{array}\right]=\left[\begin{array}{ccc}{Z}_{11}& Z_{12}& Z_{13}\\ Z_{21}& Z_{22}& Z_{23}\\ Z_{31}& Z_{32}& Z_{33}\end{array}\right]\left[\begin{array}{c}{I}_1\\ I_2\\ I_3\end{array}\right]$

However the following representations are necessarily limited to two-port devices:

• Hybrid (h) parameters
• Inverse hybrid (g) parameters
• Transmission (ABCD) parameters
• Scattering transfer (T) parameters

Collapsing a two-port to a one port

A two-port network has four variables with two of them being independent. If one of the ports is terminated by a load with no independent sources, then the load enforces a relationship between the voltage and current of that port. A degree of freedom is lost. The circuit now has only one independent parameter. The two-port becomes a one-port impedance to the remaining independent variable.

For example, consider impedance parameters

$\left[\begin{array}{c}{V}_1\\ V_2\end{array}\right]=\left[\begin{array}{cc}{z}_{11}& z_{12}\\ z_{21}& z_{22}\end{array}\right]\left[\begin{array}{c}{I}_1\\ I_2\end{array}\right]$

Connecting a load,Z_L onto port 2 effectively adds the constraint

$V_2=-Z_L{I}_2$

The negative sign is because the positive direction for I2 is directed into the two-port instead of into the load. The augmented equations become

$\begin{array}{cc}{V}_1& =Z_{11}{I}_1+Z_{12}{I}_2\\ -Z_L{I}_2& =Z_{21}{I}_1+Z_{22}{I}_2\end{array}$

The second equation can be easily solved for I₂ as a function of I₁ and that expression can replace I₂ in the first equation leaving V₁ ( and V₂ and I₂ ) as functions of I₁

$\begin{array}{cc}{I}_2& =-\frac{Z_{21}}{Z_L+Z_{22}}{I}_1\\ V_1& =Z_{11}{I}_1-\frac{Z_{12}{Z}_{21}}{Z_L+Z_{22}}{I}_1\\ & =(Z_{11}-\frac{Z_{12}{Z}_{21}}{Z_L+Z_{22}})I_1=Z_{\mathrm{i}\mathrm{n}}{I}_1\end{array}$

So, in effect, I₁ sees an input impedance $Z_{\mathrm{i}\mathrm{n}}$ and the two-port's effect on the input circuit has been effectively collapsed down to a one-port; i.e., a simple two terminal impedance.

See also

• Admittance parameters
• Impedance parameters
• Scattering parameters
• Ray transfer matrix
• Telephone Hybrids

Notes

43 year old Petroleum Engineer Harry from Deep River, usually spends time with hobbies and interests like renting movies, property developers in singapore new condominium and vehicle racing. Constantly enjoys going to destinations like Camino Real de Tierra Adentro.

References

43 year old Petroleum Engineer Harry from Deep River, usually spends time with hobbies and interests like renting movies, property developers in singapore new condominium and vehicle racing. Constantly enjoys going to destinations like Camino Real de Tierra Adentro.

Bibliography

• Carlin, HJ, Civalleri, PP, Wideband circuit design, CRC Press, 1998. ISBN 0-8493-7897-4.
• William F. Egan, Practical RF system design, Wiley-IEEE, 2003 ISBN 0-471-20023-9.
• Farago, PS, An Introduction to Linear Network Analysis, The English Universities Press Ltd, 1961.
• 20 year-old Real Estate Agent Rusty from Saint-Paul, has hobbies and interests which includes monopoly, property developers in singapore and poker. Will soon undertake a contiki trip that may include going to the Lower Valley of the Omo.
  
  My blog: http://www.primaboinca.com/view_profile.php?userid=5889534
• Ghosh, Smarajit, Network Theory: Analysis and Synthesis, Prentice Hall of India ISBN 81-203-2638-5.
• 20 year-old Real Estate Agent Rusty from Saint-Paul, has hobbies and interests which includes monopoly, property developers in singapore and poker. Will soon undertake a contiki trip that may include going to the Lower Valley of the Omo.
  
  My blog: http://www.primaboinca.com/view_profile.php?userid=5889534
• Matthaei, Young, Jones, Microwave Filters, Impedance-Matching Networks, and Coupling Structures, McGraw-Hill, 1964.
• Mahmood Nahvi, Joseph Edminister, Schaum's outline of theory and problems of electric circuits, McGraw-Hill Professional, 2002 ISBN 0-07-139307-2.
• Dragica Vasileska, Stephen Marshall Goodnick, Computational electronics, Morgan & Claypool Publishers, 2006 ISBN 1-59829-056-8.