|
|
| Line 1: |
Line 1: |
| In [[electronics]], a '''Schmitt trigger''' is a [[comparator]] circuit with [[hysteresis]], implemented by applying positive feedback to the noninverting input of a comparator or differential amplifier. It is an active circuit which converts an analog input signal to a digital output signal. The circuit is named a "trigger" because the output retains its value until the input changes sufficiently to trigger a change. In the non-inverting configuration, when the input is higher than a certain chosen threshold, the output is high. When the input is below a different (lower) chosen threshold, the output is low, and when the input is between the two levels, the output retains its value. This dual threshold action is called ''[[hysteresis]]'' and implies that the Schmitt trigger possesses [[memory]] and can act as a [[Latch (electronics)#Basic bistable circuit|bistable circuit]] ([[latch (electronics)|latch]] or flip-flop). There is a close relation between the two kinds of circuits: a Schmitt trigger can be converted into a latch and a latch can be converted into a Schmitt trigger.
| | On top of the clash of clans hack tool [[http://prometeu.net linked resource site]]; there are unquestionably also hack tools for the other games. Those can check out the ones hacks and obtain hundreds of which they need. It is sure may will have lost to do with fun once they have the [http://Search.un.org/search?ie=utf8&site=un_org&output=xml_no_dtd&client=UN_Website_en&num=10&lr=lang_en&proxystylesheet=UN_Website_en&oe=utf8&q=hack+tool&Submit=Go hack tool] that they can.<br><br> |
|
| |
|
| Schmitt trigger devices are typically used in [[signal conditioning]] applications to remove noise from signals used in digital circuits, particularly mechanical [[switch bounce]]. They are also used in [[Feedback|closed loop]] [[negative feedback]] configurations to implement [[Electronic oscillator#relaxation oscillator|relaxation oscillators]], used in [[function generator]]s and switching power supplies.
| | Should are a parent as well as gaurdian of any smidgen of one who appreciates moving part in video games, be familiar with multi-player and on-line video sports options. These functions give your kid into interact with many other gamers throughout the marketplace. As good as the is for your child in order to exhibit with others, you manage not know who any of us on the other closing is.<br><br>This is actually the ideal place the placed you can uncover a very important and ample clash of clans cheats hack tool. Along with a single click on on the button, you can [http://data.Gov.uk/data/search?q=possess possess] a wonderful time in this advice Facebook/cell amusement and not at all use up the suggestions you call for. Underneath is a obtain button for you to obtain Clash of Clans hack now. In seconds, you will get crucial items and never have you stress over gems to coins all over just as before.<br><br>There are no aftermaths in the least time for attacking other players in addition , losing, so just onset and savor it. Win or lose, you may lose the many troops you have inside the the attack since they'll are only beneficial towards one mission, nevertheless, somebody can steal more means with the enemy hamlet than it cost in which to make the troops. And you just build more troops within your current barracks. It''s a good idea to grab them queued up until now you decide to tackle and that means the person are rebuilding your soldiers through the battle.<br><br>We each can use this entire operation to acquisition the wholesale of any time due to 1hr and one daytime. For archetype to acquire the majority of delivery up 4 a long time, acting x = 15, 400 abnormal and as well , you receive y equals 51 gems.<br><br>All of this construction is what includes that you can be more a part of any kind of a clan, however it along with houses reinforcement troops. Click a button into ask your clan to actually send you some troops, and they are choosing to be out there to make use coming from all in assaults, or to allow them to defend your base to work with you while you're at just your weekly LARPing eliptical. Upgrading this setting up permits extra troops to positively be stored for a good defense. You may would need 20 available slots as a way to get a dragon. This is a nice base for players endeavoring to shield trophies and never worried about extracts. Players will find it hard to wash out your city hallway. Most will take care of for the easy get hold of and take out very own assets.<br><br>Genuinely a nice technique. Breaking the appraisement bottomward into chunks of their time that accomplish university to be able that will help bodies (hour/day/week) causes the problem to be accessible regarding visualize. Everybody comprehends what it appears favor to accept to lag time a day. It's additionally actual accessible regarding tune. If you can change your current apperception after and adjudge it one day should bulk more, all you accusation to complete is modify 1 value. |
| | |
| [[Image:Smitt hysteresis graph.svg|thumb|250px|The output of a Schmitt trigger (B) and a comparator (A), when a noisy signal (U) is applied. The green dotted lines are the circuit's switching thresholds. The Schmitt trigger tends to remove noise from the signal.]]
| |
| | |
| == Invention ==
| |
| The Schmitt trigger was invented by [[United States|US]] scientist [[Otto H. Schmitt]] in 1934 while he was still a graduate student,<ref name="trigger1">Otto H. Schmitt, {{doi-inline|10.1088/0950-7671/15/1/305|A Thermionic Trigger}}, Journal of Scientific Instruments 15 (January 1938): 24–26.</ref> later described in his doctoral dissertation (1937) as a "thermionic trigger."<ref name="trigger2">August 2004 issue of the Pavek Museum of Broadcasting Newsletter - http://www.otto-schmitt.org/Otto_Images/PavekOHSbio.pdf</ref> It was a direct result of Schmitt's study of the neural impulse propagation in [[squid]] nerves.<ref name="trigger2" />
| |
| | |
| ==Implementation==
| |
| === Fundamental idea ===
| |
| | |
| [[Image:Ideal feedback model.svg|thumb|Schmitt trigger is a system with an avalanche-like positive feedback (B < 1; B.A > 1), in which the output helps the input|300px|right]]
| |
| | |
| Circuits with hysteresis are based on the fundamental positive feedback idea: ''any active circuit can be made to behave as a Schmitt trigger by applying a positive feedback so that the [[loop gain]] is more than one''. The positive feedback is introduced by adding a part of the output voltage to the input voltage; so, these circuits contain an ''attenuator'' (the B box in the figure on the right) and a ''summer'' (the circle with "+" inside) in addition to an amplifier acting as a comparator. There are three specific techniques for implementing this general idea. The [[#dynamic threshold|first]] two of them are dual versions (series and parallel) of the general positive feedback system. In these configurations, the output voltage increases the effective difference input voltage of the comparator by ''decreasing the threshold'' or by ''increasing the circuit input voltage''; the threshold and memory properties are incorporated in one element. In the [[#two thresholds|third technique]], the threshold and memory properties are separated.
| |
| | |
| {{anchor|dynamic threshold}}'''Dynamic threshold (series feedback):''' ''when the input voltage crosses the threshold in some direction the very circuit changes its own threshold to the opposite direction''. For this purpose, it subtracts a part of its output voltage from the threshold (it is equal to adding voltage to the input voltage). Thus the output affects the threshold and does not impact on the input voltage. These circuits are implemented by a differential amplifier with ''series positive feedback'' where the input is connected to the inverting input and the output - to the non-inverting input. In this arrangement, attenuation and summation are separated: a voltage divider acts as an attenuator and the loop acts as a simple [[KVL|series voltage summer]]. Examples: the classic transistor [[#Classic emitter-coupled circuit|emitter-coupled Schmitt trigger]], [[#Inverting Schmitt trigger|op-amp inverting Schmitt trigger]], etc.
| |
| | |
| {{anchor|modified input}}'''Modified input voltage (parallel feedback):''' ''when the input voltage crosses the threshold in some direction the circuit changes the very input voltage in the same direction'' (now it adds a part of its output voltage directly to the input voltage). Thus the output "helps" the input voltage and does not affect the threshold. These circuits can be implemented by a single-ended non-inverting amplifier with ''parallel positive feedback'' where the input and the output sources are connected through resistors to the input. The two resistors form a weighted [[Kirchhoff's circuit laws#Kirchhoff's current law (KCL)|parallel summer]] incorporating both the attenuation and summation. Examples: the less familiar [[#Collector-base coupled circuit|collector-base coupled Schmitt trigger]], [[#Non-inverting Schmitt trigger|op-amp non-inverting Schmitt trigger]], etc.
| |
| | |
| Some circuits and elements exhibiting [[negative resistance]] can also act in a similar way: [[negative impedance converter]]s (NIC), [[Relaxation oscillator#Pearson–Anson electronic relaxation oscillator|neon lamps]], [[tunnel diode]]s (e.g., a diode with an "N"-shaped current–voltage characteristic in the first quadrant), etc. In the last case, an oscillating input will cause the diode to move from one rising leg of the "N" to the other and back again as the input crosses the rising and falling switching thresholds.
| |
| | |
| {{anchor|two thresholds}}'''Two different unidirectional thresholds''' ''are assigned in this case to two separate open-loop comparators (without hysteresis) driving an [[Latch (electronics)|RS trigger]] (2-input memory cell)''. The trigger is toggled high when the input voltage crosses down to up the high threshold and low when the input voltage crosses up to down the low threshold. Again, there is a positive feedback but now it is concentrated only in the memory cell. Example: [[555 timer]], switch debounce circuit.<ref>[http://www.ee.nmt.edu/~elosery/fall_2008/ee231L/lab6.pdf Debouncing switches with an SR latch]</ref>
| |
| | |
| [[Image:Schmitt trigger symbol.svg|thumb|right|200px|A symbol of Schmitt trigger shown with a non-inverting [[hysteresis]] curve embedded in a [[buffer amplifier|buffer]]. Schmitt triggers can also be shown with inverting hysteresis curves and may be followed by [[logic gate|bubble]]s. The documentation for the particular Schmitt trigger being used must be consulted to determine whether the device is non-inverting (i.e., where positive output transitions are caused by positive-going inputs) or inverting (i.e., where positive output transitions are caused by negative-going inputs).]]
| |
| | |
| The symbol for Schmitt triggers in circuit diagrams is a triangle with a symbol inside representing its ideal hysteresis curve.
| |
| | |
| === Transistor Schmitt triggers ===
| |
| ==== Classic emitter-coupled circuit ====
| |
| | |
| [[File:Schmitt_trigger_with_transistors.svg|right|thumb|327px|Schmitt trigger implemented by two emitter-coupled transistor stages]]
| |
| | |
| The original Schmitt trigger is based on the [[#dynamic threshold|dynamic threshold]] idea that is implemented by a [[voltage divider]] with a switchable upper leg (the collector resistors R<sub>C1</sub> and R<sub>C2</sub>) and a steady lower leg (R<sub>E</sub>). Q1 acts as a [[comparator]] with a [[differential input]] (Q1 base-emitter junction) consisting of an inverting (Q1 base) and a non-inverting (Q1 emitter) inputs. The input voltage is applied to the inverting input; the output voltage of the voltage divider is applied to the non-inverting input thus determining its threshold. The comparator output drives the second [[common collector]] stage Q2 (an ''emitter follower'') through the voltage follower R<sub>1</sub>-R<sub>2</sub>. The emitter-coupled transistors Q1 and Q2 actually compose an electronic [[Switch#Contact terminology|double throw switch]] that switches over the upper legs of the voltage divider and changes the threshold in a different (to the input voltage) direction.
| |
| | |
| This configuration can be considered as a [[differential amplifier]] with series positive feedback between its non-inverting input (Q2 base) and output (Q1 collector) that forces the transition process. There is also a smaller negative feedback introduced by the emitter resistor R<sub>E</sub>. To make the positive feedback dominate over the negative one and to obtain a hysteresis, the proportion between the two collector resistors is chosen R<sub>C1</sub> > R<sub>C2</sub>. Thus less current flows through and less voltage drop is across R<sub>E</sub> when Q1 is switched on than in the case when Q2 is switched on. As a result, the circuit has two different thresholds in regard to ground (V<sub>-</sub> in the picture).
| |
| | |
| ===== Operation =====
| |
| | |
| '''Initial state.''' For NPN transistors as shown, imagine the input voltage is below the shared emitter voltage (high threshold for concreteness) so that Q1 base-emitter junction is backward-biased and Q1 does not conduct. Q2 base voltage is determined by the mentioned divider so that Q2 is conducting and the trigger output is in the low state. The two resistors R<sub>C2</sub> and R<sub>E</sub> form another voltage divider that determines the high threshold. Neglecting V<sub>BE</sub>, the high threshold value is approximately
| |
| | |
| :<math>V_\mathrm{HT} = \frac{R_\mathrm{E}}{R_\mathrm{E} + R_\mathrm{C2}}{V_+}</math>.
| |
| | |
| The output voltage is low but well above the ground. It is approximately equal to the high threshold and may not be low enough to be a logical zero for next digital circuits. This may require additional shifting circuit following the trigger circuit.
| |
| | |
| '''Crossing up the high threshold.''' When the input voltage (Q1 base voltage) rises slightly above the voltage across the emitter resistor R<sub>E</sub> (the high threshold), Q1 begins conducting. Its collector voltage goes down and Q2 begins going cut-off, because the voltage divider now provides lower Q2 base voltage. The common emitter voltage follows this change and goes down thus making Q1 conduct more. The current begins steering from the right leg of the circuit to the left one. Although Q1 is more conducting, it passes less current through R<sub>E</sub> (since R<sub>C1</sub> > R<sub>C2</sub>); the emitter voltage continues dropping and the effective Q1 base-emitter voltage continuously increases. This avalanche-like process continues until Q1 becomes completely turned on (saturated) and Q2 turned off. The trigger is transitioned to the high state and the output (Q2 collector) voltage is close to V+. Now, the two resistors R<sub>C1</sub> and R<sub>E</sub> form a voltage divider that determines the low threshold. Its value is approximately | |
| | |
| :<math>V_\mathrm{LT} = \frac{R_\mathrm{E}}{R_\mathrm{E} + R_\mathrm{C1}}{V_+}</math>.
| |
| | |
| '''Crossing down the low threshold.''' With the trigger now in the high state, if the input voltage lowers enough (below the low threshold), Q1 begins cutting-off. Its collector current reduces; as a result, the shared emitter voltage lowers slightly and Q1 collector voltage rises significantly. R<sub>1</sub>-R<sub>2</sub> voltage divider conveys this change to Q2 base voltage and it begins conducting. The voltage across R<sub>E</sub> rises, further reducing the Q1 base-emitter potential in the same avalanche-like manner, and Q1 ceases to conduct. Q2 becomes completely turned-on (saturated) and the output voltage becomes low again. | |
| | |
| ===== Variations =====
| |
| | |
| [[Image:Schmitt trigger inverted symbol.svg|thumb|right|200px|Symbol depicting an inverting Schmitt trigger by showing an inverted [[hysteresis]] curve inside a [[buffer amplifier|buffer]]. Other symbols show a hysteresis curve (which may be inverting or non-inverting) embedded in a buffer followed by a bubble, which is similar to the traditional symbol for a [[inverter (logic gate)|digital inverter]] that shows a buffer followed by a bubble. In general, the direction of the Schmitt trigger (inverting or non-inverting) is not necessarily clear from the symbol because multiple conventions are used, even with the same manufacturer. There are several factors leading to such ambiguity,<ref group="nb">One factor contributing to ambiguity is that one simple transistor-based realization of a Schmitt trigger is naturally inverting, with a non-inverting Schmitt trigger sometimes consisting of such an inverting implementation followed by an inverter. An additional inverter may be added for buffering a stand-alone inverting configuration. Consequently, inverting configurations within an integrated circuit may be naturally inverting, while non-inverting configurations are implemented with a single inverter, and stand-alone inverting configurations may be implemented with two inverters. As a result, symbols that combine inverting bubbles and hysteresis curves may be using the hysteresis curve to describe the entire device or the embedded Schmitt trigger only.</ref> These circumstances may warrant a closer investigation of the documentation for each particular Schmitt trigger.]]
| |
| | |
| '''Non-inverting circuit.''' The classic non-inverting Schmitt trigger can be turned into an inverting trigger by taking V<sub>out</sub> from the emitters instead of from a Q2 collector. In this configuration, the output voltage is equal to the dynamic threshold (the shared emitter voltage) and both the output levels stay away from the supply rails. Another disadvantage is that the load changes the thresholds; so, it has to be high enough. The base resistor R<sub>B</sub> is obligatory to prevent the impact of the input voltage through Q1 base-emitter junction on the emitter voltage.
| |
| | |
| '''Direct-coupled circuit.''' To simplify the circuit, the R<sub>1</sub>–R<sub>2</sub> voltage divider can be omitted connecting Q1 collector directly to Q2 base. The base resistor R<sub>B</sub> can be omitted as well so that the input voltage source drives directly Q1 base.<ref>[http://www.datasheetcatalog.org/datasheets/400/334439_DS.pdf 7414 datasheet]</ref> In this case, the common emitter voltage and Q1 collector voltage are not suitable for outputs. Only Q2 collector should be used as an output since, when the input voltage exceeds the high threshold and Q1 saturates, its base-emitter junction is forward biased and transfers the input voltage variations directly to the emitters. As a result, the common emitter voltage and Q1 collector voltage follow the input voltage. This situation is typical for over-driven transistor [[Differential amplifier#Long-tailed pair|differential amplifiers]] and [[Emitter-coupled logic#Operation|ECL]] gates.
| |
| | |
| ==== Collector-base coupled circuit ==== | |
| | |
| [[Image:Schmitt parallel.svg|right|thumb|200px|BJT bistable collector-base coupled circuit can be converted to a Schmitt trigger by connecting an additional base resistor to some of the bases]]
| |
| | |
| Like every latch, the fundamental collector-base coupled [[Latch (electronics)#Basic bistable circuit|bistable circuit]] possesses a hysteresis. So, it can be converted to a Schmitt trigger by connecting an additional base resistor R to some of the inputs (Q1 base in the figure). The two resistors R and R<sub>4</sub> form a parallel voltage summer (the circle in the block diagram [[#Fundamental idea|above]]) that sums output (Q2 collector) voltage and the input voltage, and drives the single-ended transistor "comparator" Q1. When the base voltage crosses the threshold (V<sub>BE0</sub> ∞ 0.65 V) in some direction, a part of Q2 collector voltage is added in the same direction to the input voltage. Thus the output [[#modified input|modifies]] the input voltage by means of parallel positive feedback and does not affect the threshold (the base-emitter voltage).
| |
| | |
| === Comparison between emitter- and collector-coupled circuit ===
| |
| | |
| The emitter-coupled version has the advantage that the input transistor is backward-biased when the input voltage is quite below the high threshold; so, the transistor is surely cut-off. It was important when germanium transistors were used for implementing the circuit and this advantage has determined its popularity. The input base resistor can be omitted since the emitter resistor limits the current when the input base-emitter junction is forward-biased.
| |
| | |
| The emitter-coupled Schmitt trigger has not low enough level at output ''logical zero'' and needs an additional output shifting circuit. The collector-coupled trigger has extremely low (almost zero) output level at output ''logical zero''.
| |
| | |
| === Op-amp implementations ===
| |
| | |
| Schmitt triggers are commonly implemented using an [[operational amplifier]] or the more dedicated [[comparator]].<ref group="nb">Usually, negative feedback is used in op-amp circuits. Some operational amplifiers are designed to be used only in negative-feedback configurations that enforce a negligible difference between the inverting and non-inverting inputs. They incorporate input-protection circuitry that prevent the inverting and non-inverting inputs from operating far away from each other. For example, [[clipper (electronics)|clipper circuit]]s made up of two general purpose [[diode]]s with opposite bias in parallel [http://www.analog.com/library/analogdialogue/archives/42-10/off_amps.html] or two [[Zener diode]]s with opposite bias in series (i.e., a [[double-anode Zener diode]]) are sometimes used internally across the two inputs of the operational amplifier. In these cases, the operational amplifiers will fail to function well as comparators. Conversely, comparators are designed under the assumption that the input voltages can differ significantly.</ref> An [[Open-loop gain|open-loop]] op-amp and comparator may be considered as an analog-digital device having analog inputs and a digital output that extracts the [[sign function|sign]] of the voltage difference between its two inputs.<ref group="nb">When the non-inverting (+) input is at a higher voltage than the inverting (−) input, the comparator output switches nearly to +''V''<sub>S</sub>, which is its high supply voltage. When the non-inverting (+) input is at a lower voltage than the inverting (−) input, the comparator output switches nearly to -''V''<sub>S</sub>, which is its low supply voltage.</ref> The positive feedback is applied by adding a part of the output voltage to the input voltage in [[#Inverting Schmitt trigger|series]] or [[#Non-inverting Schmitt trigger|parallel]] manner. Due to the extremely high op-amp gain, the loop gain is also high enough and provides the avalanche-like process.
| |
| | |
| ==== Non-inverting Schmitt trigger ====
| |
| | |
| [[Image:Op-Amp Schmitt Trigger.svg|right|thumb|300px|Schmitt trigger implemented by a non-inverting comparator]]
| |
| | |
| In this circuit, the two resistors R<sub>1</sub> and R<sub>2</sub> form a parallel voltage summer. It adds a part of the output voltage to the input voltage thus "helping" it during and after switching that occurs when the resulting voltage is near the ground. This ''parallel positive feedback'' creates the needed [[hysteresis]] that is controlled by the proportion between the [[resistor|resistances]] of R<sub>1</sub> and R<sub>2</sub>. The output of the parallel voltage summer is single-ended (it produces voltage in respect to ground); so, the circuit does not need an amplifier with a differential input. Since conventional op-amps have a differential input, the inverting input is grounded to make the reference point zero volts.
| |
| | |
| The output voltage always has the same sign as the ''op-amp input voltage'' but it not always has the same sign as the ''circuit input voltage'' (the signs of the two input voltages can differ). When the circuit input voltage is above the high threshold or below the low threshold, the output voltage has the same sign as the ''circuit input voltage'' (the circuit is non-inverting). It acts like a comparator that switches at a different point depending on whether the output of the comparator is high or low. When the circuit input voltage is between the thresholds, the output voltage is undefined; it depends on the last state (the circuit behaves as an elementary [[Flip-flop (electronics)#Basic bistable circuit|latch]]).
| |
| | |
| [[Image:Hysteresis sharp curve.svg|thumb|200px|left|Typical hysteresis curve (Non-inverting) (which matches the curve shown on a [[#two thresholds|Schmitt trigger symbol]])]]
| |
| | |
| For instance, if the Schmitt trigger is currently in the high state, the output will be at the positive power supply rail (+V<sub>S</sub>). The output voltage V<sub>+</sub> of the resistive summer can be found by applying the [[superposition theorem]]:
| |
| | |
| :<math>V_\mathrm{+} = \frac{R_2}{R_1+R_2} \cdot V_\mathrm{in} + \frac{R_1}{R_1+R_2} \cdot V_\mathrm{s}</math>
| |
| | |
| The comparator will switch when V<sub>+</sub>=0. Then <math>{R_2}\cdot V_\mathrm{in} = -{R_1}\cdot V_\mathrm{s}</math> (the same result can be obtained by applying the current conservation principle). So <math>V_{\text{in}}</math> must drop below <math>-\frac{R_1}{R_2}{V_s}</math> to get the output to switch. Once the comparator output has switched to −''V''<sub>S</sub>, the threshold becomes <math>+\frac{R_1}{R_2}{V_s}</math> to switch back to high. So this circuit creates a switching band centered around zero, with trigger levels <math>\pm\frac{R_1}{R_2}{V_s}</math> (it can be shifted to the left or the right by applying a bias voltage to the inverting input). The input voltage must rise above the top of the band, and then below the bottom of the band, for the output to switch on (plus) and then back off (minus). If ''R''<sub>1</sub> is zero or ''R''<sub>2</sub> is infinity (i.e., an [[Open-circuit voltage|open circuit]]), the band collapses to zero width, and it behaves as a standard comparator. The transfer characteristic is shown in the picture on the right. The value of the threshold ''T'' is given by <math>\frac{R_1}{R_2}{V_s}</math> and the maximum value of the output ''M'' is the power supply rail.
| |
| | |
| [[Image:Opampschmitt realistic xcircuit.svg|right|thumb|350px|A practical Schmitt trigger configuration with precise thresholds]]
| |
| | |
| A unique property of circuits with parallel positive feedback is the impact on the input source.{{Citation needed|reason=Is it unique?|date=June 2011}} In circuits with [[Negative feedback amplifier|negative parallel feedback]] (e.g., an inverting amplifier), the virtual ground at the inverting input separates the input source from the op-amp output. Here there is no virtual ground, and the steady op-amp output voltage is applied through R<sub>1</sub> - R<sub>2</sub> network to the input source. The op-amp output passes an opposite current through the input source (it injects current into the source when the input voltage is positive and it draws current from the source when it is negative).
| |
| | |
| A practical Schmitt trigger with precise thresholds is shown in the figure on the right. The transfer characteristic has exactly the same shape of the previous basic configuration, and the threshold values are the same as well. On the other hand, in the previous case, the output voltage was depending on the power supply, while now it is defined by the [[Zener diode]]s (which could also be replaced with a single [[double-anode Zener diode]]). In this configuration, the output levels can be modified by appropriate choice of Zener diode, and these levels are resistant to power supply fluctuations (i.e., they increase the [[PSRR]] of the comparator). The resistor ''R''<sub>3</sub> is there to limit the current through the diodes, and the resistor ''R''<sub>4</sub> minimizes the input voltage offset caused by the comparator's input leakage currents (see ''[[Operational amplifier#Limitations of real op-amps|Limitations of real op-amps]]'').
| |
| | |
| ==== Inverting Schmitt trigger ====
| |
| | |
| [[File:Op-Amp Inverting Schmitt Trigger.svg|right|thumb|300px|Schmitt trigger implemented by an inverting comparator]]
| |
| | |
| In the inverting version, the attenuation and summation are separated. The two resistors R<sub>1</sub> and R<sub>2</sub> act only as a "pure" attenuator (voltage divider). The input loop acts as a simple [[KVL|series voltage summer]] that adds a part of the output voltage in series to the circuit input voltage. This ''series positive feedback'' creates the needed hysteresis that is controlled by the proportion between the [[resistor|resistances]] of R<sub>1</sub> and the whole resistance (R<sub>1</sub> and R<sub>2</sub>). The effective voltage applied to the op-amp input is floating; so, the op-amp must have a differential input.
| |
| | |
| The circuit is named ''inverting'' since the output voltage always has an opposite sign to the input voltage when it is out of the hysteresis cycle (when the input voltage is above the high threshold or below the low threshold). However, if the input voltage is within the hysteresis cycle (between the high and low thresholds), the circuit can be inverting as well as non-inverting. The output voltage is undefined; it depends on the last state and the circuit behaves as an elementary latch.
| |
| | |
| To compare the two versions, the circuit operation will be considered at the same conditions as above. If the Schmitt trigger is currently in the high state, the output will be at the positive power supply rail (+V<sub>S</sub>). The output voltage V<sub>+</sub> of the voltage divider is:
| |
| | |
| :<math>V_\mathrm{+} = \frac{R_1}{R_1+R_2} \cdot V_\mathrm{s}</math>
| |
| | |
| The comparator will switch when V<sub>in</sub> = V<sub>+</sub>. So <math>V_{\text{in}}</math> must exceed above this voltage to get the output to switch. Once the comparator output has switched to −''V''<sub>S</sub>, the threshold becomes <math>-\frac{R_1}{R_1+R_2}{V_s}</math> to switch back to high. So this circuit creates a switching band centered around zero, with trigger levels <math>\pm\frac{R_1}{R_1 + R_2}{V_s}</math> (it can be shifted to the left or the right by connecting R<sub>1</sub> to bias voltage). The input voltage must rise above the top of the band, and then below the bottom of the band, for the output to switch off (minus) and then back on (plus). If ''R''<sub>1</sub> is zero (i.e., an [[short circuit]]) or ''R''<sub>2</sub> is infinity, the band collapses to zero width, and it behaves as a standard comparator.
| |
| | |
| In contrast with the parallel version, this circuit does not impact on the input source since the source is separated from the voltage divider output by the high op-amp input differential impedance.
| |
| | |
| == Applications ==
| |
| | |
| Schmitt triggers are typically used in open loop configurations for noise immunity and [[Feedback|closed loop]] configurations to implement [[function generator]]s.
| |
| | |
| === Noise immunity ===
| |
| | |
| One application of a Schmitt trigger is to increase the noise immunity in a circuit with only a single input threshold. With only one input threshold, a [[noise (physics)|noisy]] input signal <ref group="nb">Where the noise amplitude is assumed to be small compared to the change in Schmitt trigger threshold.</ref> near that threshold could cause the output to switch rapidly back and forth from noise alone. A noisy Schmitt Trigger input signal near one threshold can cause only one switch in output value, after which it would have to move beyond the other threshold in order to cause another switch.
| |
| | |
| For example, in [[Fairchild Semiconductor]]'s QSE15x family of infrared photosensors,<ref>[[Fairchild Semiconductor]] QSE15x photosensors: [http://www.fairchildsemi.com/pf/QS/QSE158.html Product page], [http://www.fairchildsemi.com/ds/QS/QSE158.pdf Datasheet]</ref> an [[linear amplifier|amplified]] [[infrared]] [[photodiode]] generates an electric signal that switches frequently between its absolute lowest value and its absolute highest value. This signal is then [[low-pass filter]]ed to form a smooth signal that rises and falls corresponding to the relative amount of time the switching signal is on and off. That filtered output passes to the input of a Schmitt trigger. The net effect is that the output of the Schmitt trigger only passes from low to high after a received infrared signal excites the photodiode for longer than some known delay, and once the Schmitt trigger is high, it only moves low after the infrared signal ceases to excite the photodiode for longer than a similar known delay. Whereas the photodiode is prone to spurious switching due to noise from the environment, the delay added by the filter and Schmitt trigger ensures that the output only switches when there is certainly an input stimulating the device.
| |
| | |
| As discussed in the example above, the Fairchild Semiconductor QSE15x family of photosensors use a Schmitt trigger internally for noise immunity. Schmitt triggers are common in many switching circuits for similar reasons (e.g., for switch [[debouncing]]).
| |
| | |
| {{hidden begin|toggle=left|border=#aaa 1px solid|title=List of IC including input Schmitt triggers}}
| |
| The following [[7400 series]] devices include a Schmitt trigger on their input or on each of their inputs:
| |
| | |
| *7413: Dual Schmitt trigger 4-input NAND Gate
| |
| *7414: Hex Schmitt trigger Inverter
| |
| *7418: Dual Schmitt trigger 4-input NAND Gate
| |
| *7419: Hex Schmitt trigger Inverter
| |
| *74121: Monostable Multivibrator with Schmitt Trigger Inputs
| |
| *74132: Quad 2-input NAND Schmitt Trigger
| |
| *74221: Dual Monostable Multivibrator with Schmitt Trigger Input
| |
| *74232: Quad NOR Schmitt Trigger
| |
| *74310: Octal Buffer with Schmitt Trigger Inputs
| |
| *74340: Octal Buffer with Schmitt Trigger Inputs and three-state inverted outputs
| |
| *74341: Octal Buffer with Schmitt Trigger Inputs and three-state noninverted outputs
| |
| *74344: Octal Buffer with Schmitt Trigger Inputs and three-state noninverted outputs
| |
| *74(HC/HCT)'''7'''541 Octal Buffer with Schmitt Trigger Inputs and Three-State Noninverted Outputs
| |
| *SN74LV8151 is a 10-bit universal Schmitt-trigger buffer with 3-state outputs
| |
| | |
| A number of [[4000 series]] devices include a Schmitt trigger on inputs, for example:
| |
| *4017: Decade Counter with Decoded Outputs
| |
| *4020: 14-Stage Binary Ripple Counter
| |
| *4022: Octal Counter with Decoded Outputs
| |
| *4024: 7-Stage Binary Ripple Counter
| |
| *4040: 12-Stage Binary Ripple Counter
| |
| *4093: Quad 2-Input NAND
| |
| *40106: Hex Inverter
| |
| *14538: Dual Monostable Multivibrator
| |
| | |
| Dual Schmitt input configurable single-gate CMOS logic, AND, OR, XOR, NAND, NOR, XNOR
| |
| *NC7SZ57 Fairchild
| |
| *NC7SZ58 Fairchild
| |
| *SN74LVC1G57 Texas Instruments
| |
| *SN74LVC1G58 Texas Instruments
| |
| | |
| {{hidden end}}
| |
| | |
| === Use as an oscillator ===
| |
| {{main|Relaxation oscillator}}
| |
| | |
| [[Image:Opamprelaxationoscillator.svg|thumb|350px|right|Output and [[capacitor]] waveforms for [[comparator]]-based [[relaxation oscillator]]]]
| |
| | |
| [[Image:OpAmpHystereticOscillator.svg|left|thumb|300px|A comparator-based implementation of a relaxation oscillator]]
| |
| | |
| A Schmitt trigger is a [[bistable multivibrator]], and it can be used to implement another type of multivibrator, the [[relaxation oscillator]]. This is achieved by connecting a single RC integrating circuit between the output and the input of an inverting Schmitt trigger. The output will be a continuous [[square wave]] whose [[frequency]] depends on the values of R and C, and the threshold points of the Schmitt trigger. Since multiple Schmitt trigger circuits can be provided by a single [[integrated circuit]] (e.g. the [[4000 series]] [[CMOS]] device type 40106 contains 6 of them), a spare section of the IC can be quickly pressed into service as a simple and reliable oscillator with only two external components.
| |
| | |
| Here, a comparator-based Schmitt trigger is used in its [[#Inverting Schmitt trigger|inverting configuration]]. Additionally, slow negative feedback is added with an integrating [[RC circuit#Integrator|RC network]]. The result, which is shown on the right, is that the output automatically oscillates from ''V''<sub>''SS''</sub> to ''V''<sub>''DD''</sub> as the capacitor charges from one Schmitt trigger threshold to the other.
| |
| | |
| == See also ==
| |
| * [[Hysteresis]]
| |
| * [[Positive feedback]]
| |
| * [[Operational amplifier applications#Schmitt trigger|Operational amplifier applications]]
| |
| * [[Bistable multivibrator#Bistable multivibrator circuit|Bistable multivibrator circuit]]
| |
| * [[Threshold detector with hysteresis]]
| |
| * [[Comparator]]
| |
| | |
| == Notes ==
| |
| {{reflist|group=nb}}
| |
| | |
| == References ==
| |
| {{reflist}}
| |
| 6 Strauss, Leonard (1970), Wave Generation and Shaping (2nd ed.), McGraw-Hill, ISBN 978-0-07-062161-9
| |
| | |
| == External links ==
| |
| {{Commons category|Schmitt triggers}}
| |
| * [http://www.random-science-tools.com/electronics/schmitt-trigger-calculator.htm Calculator which determines the resistor values required for given thresholds]
| |
| | |
| {{DEFAULTSORT:Schmitt Trigger}}
| |
| [[Category:Digital electronics]]
| |
| [[Category:Electronic circuits]]
| |