|
|
| Line 1: |
Line 1: |
| {{Refimprove|date=July 2011}}
| | I'm Yoshiko Oquendo. My job is a production and distribution officer and I'm performing fairly good monetarily. To play badminton is something he truly enjoys doing. He currently life in Idaho and his parents live close by.<br><br>Feel free to visit my page; [http://Www.Tobynabors.com/ActivityFeed/MyProfile/tabid/61/userId/46195/Default.aspx vehicle extended warranty] |
| [[File:Centrifugal fan.gif|thumb|right|275px|A typical backward-curved centrifugal fan, where the blades curve in the opposite direction than the one they rotate in]]
| |
| A '''centrifugal fan''' is a mechanical device for moving [[air]] or other [[gas]]es. The terms "blower" and "squirrel cage fan" (because it looks like a [[hamster wheel]]) are frequently used as synonyms. These fans increase the speed of air stream with the rotating [[impeller]]s.<ref name="Fans and Blowers">{{cite book|title=Electrical Energy Equipment: Fans and Blowers|year=2006|publisher=UNEP|pages=21}}</ref>
| |
| They use the kinetic energy of the [[impeller]]s or the rotating blade to increase the pressure of the air/gas stream which in turn moves them against the resistance caused by ducts, dampers and other components. Centrifugal fans accelerate air radially, changing the direction (typically by 90<sup>o</sup>) of the airflow. They are sturdy, quiet, reliable, and capable of operating over a wide range of conditions.<ref name="ACMA sourcebook">{{cite book|last=Lawrence Berkeley National Laboratory Washington, DC Resource Dynamics Corporation Vienna, VA|title=Improving Fan System Performance|url=http://www1.eere.energy.gov/manufacturing/tech_deployment/pdfs/fan_sourcebook.pdf|accessdate=29 February 2012|page=21}}</ref>
| |
| | |
| Centrifugal fans are constant [[Actual cubic feet per minute|CFM]] devices or constant volume devices, meaning that, at a constant fan speed, a centrifugal fan will pump a constant volume of air rather than a constant mass. This means that the air velocity in a system is fixed even though mass flow rate through the fan is not.
| |
| | |
| The centrifugal fan is one of the most widely used fans. Centrifugal fans are by far the most prevalent type of fan used in the [[Heating, Ventilation, and Air Conditioning|HVAC]] industry today. They are usually cheaper than axial fans and simpler in construction.<ref name="estar air">{{cite web|title=Air Distribution Systems|url=http://www.energystar.gov/index.cfm?c=business.EPA_BUM_CH8_AirDistSystems#SS_8_3_1|publisher=Energy Star|accessdate=29 February 2012}}</ref><!-----Don't give line break----->
| |
| It is used in transporting gas or materials and in ventilation system for buildings.<ref name="Singh IITM">{{cite journal|last=Singh|first=O.P.|coauthors=Rakesh Khilwani, T. Sreenivasulu, M. Kannan|title=PARAMETRIC STUDY OF CENTRIFUGAL FAN PERFORMANCE: EXPERIMENTS AND NUMERICAL SIMULATION|journal=International Journal of Advances in Engineering & Technology|date=May 2011|volume=1|issue=2|pages=18|doi=|pmid=|url=http://www.ijaet.org/media/0001/5PARAMETRIC-STUDY-OF-CENTRIFUGAL-FAN-PERFORMANCE-EXPERIMENTS-AND-NUMERICAL-SIMULATION-Copyright-IJAET.pdf|accessdate=29 February 2012|issn=2231-1963}}</ref> They are also used commonly in central heating/cooling systems. They are also well-suited for [[Industry|industrial]] processes and [[air pollution]] control systems.
| |
| | |
| It has a [[fan (mechanical)|fan]] [[wheel]] composed of a number of fan [[blade]]s, or [[ribs]], mounted around a hub. As shown in Figure 1, the hub turns on a [[driveshaft]] that passes through the fan housing. The gas enters from the side of the fan [[wheel]], turns 90 degrees and [[accelerate]]s due to [[centrifugal force]] as it flows over the fan blades and exits the fan housing.<ref name=EPA>[http://www.epa.gov/apti/bces/module5/fans/types/types.htm#types Fan types] ([[United States Environmental Protection Agency|U.S. Environmental Protection Agency]] website page)</ref>
| |
| | |
| The centrifugal fan was invented by Russian military engineer [[Alexander Sablukov]] in 1832, and found its usage both in the Russian light industry (such as sugar making) and abroad.<ref>[http://www.elcomspb.ru/wiki/eltech_history/vent_invent/ A History of Mechanical Fan] {{ru icon}}</ref>
| |
| | |
| ==Construction==
| |
| [[Image:CentrifugalFan.png|thumb|right|275px|Figure 1: Components of a centrifugal fan]]
| |
| Main parts of a centrifugal fan are :
| |
| #Fan Housing
| |
| #[[Impeller]]s
| |
| #Inlet and outlet ducts
| |
| #[[Drive Shaft]]
| |
| #Drive mechanism
| |
| Other components used may include [[bearing (mechanical)|bearing]]s, [[coupling]]s, impeller locking device, fan discharge casing, shaft seal plates etc.<ref>{{cite web|title=TECHNICAL SPECIFICATION OF CENTRIFUGAL FANS DESIGN|url=http://www.flaktwoods.com/b02672b3-dc6f-442d-8e7f-0319f77799ad|accessdate=29 February 2012}}</ref>
| |
| | |
| ===Types of drive mechanisms===
| |
| | |
| The fan drive determines the speed of the fan wheel (impeller) and the extent to which this speed can be varied. There are three basic types of fan drives.<ref name=EPA/>
| |
| | |
| ====Direct drive====
| |
| | |
| The fan wheel can be linked directly to the shaft of an [[electric motor]]. This means that the fan wheel speed is identical to the motor's [[rotation]]al speed. With this type of fan drive mechanism, the fan speed cannot be varied unless the motor speed is adjustable. Air conditioning will then automatically provide faster speed because colder air is more dense.
| |
| | |
| Some electronics manufacturers have made centrifugal fans with external rotor motors (the stator is inside the rotor), and the rotor is directly mounted on the fan wheel (impeller).
| |
| | |
| ====Belt drive====
| |
| A set of [[sheave]]s are mounted on the motor shaft and the fan wheel shaft, and a belt transmits the mechanical energy from the motor to the fan.
| |
| | |
| The fan wheel speed depends upon the [[ratio]] of the diameter of the motor sheave to the diameter of the fan wheel sheave and can be obtained from this equation:<ref name=EPA/>
| |
| | |
| Very few people and manufacturers use chain-drive fans due to their greater noise output and complex workup, but they are more durable and don't require frequent replacement.
| |
| | |
| <math>rpm_{fan} = rpm_{motor}\,\bigg(\frac{\,D_{motor}}{D_{fan}}\bigg)</math>
| |
| {| border="0" cellpadding="2"
| |
| |-
| |
| |align=left|where:
| |
| |
| |
| |-
| |
| !align=right|<math>rpm_{fan}</math>
| |
| |align=left|= fan wheel speed, revolutions per minute
| |
| |-
| |
| !align=right|<math>rpm_{motor}</math>
| |
| |align=left|= motor nameplate speed, revolutions per minute
| |
| |-
| |
| !align=right|<math> D_{motor}</math>
| |
| |align=left|= diameter of the motor sheave
| |
| |-
| |
| !align=right|<math>D_{fan}</math>
| |
| |align=left|= diameter of the fan wheel sheave
| |
| |}
| |
| | |
| Fan wheel speeds in belt-driven fans are fixed unless the belt(s) slip. Belt slippage can reduce the fan wheel speed by several hundred revolutions per minute (rpm).
| |
| | |
| ====Variable drive====
| |
| | |
| Variable drive fans use [[Hydraulic coupling|hydraulic]] or [[Magnetic coupling]]s (between the fan wheel shaft and the motor shaft) that allow r speed. The fan speed controls are often integrated into [[automate]]d systems to maintain the desired fan wheel speed.<ref name=EPA/>
| |
| | |
| An alternate method of varying the fan speed is by use of an electronic variable-speed drive which controls the speed of the motor driving the fan. This offers better overall energy efficiency at reduced speeds than mechanical couplings.
| |
| | |
| ===Bearings===
| |
| | |
| Bearings are an important part of a fan.
| |
| | |
| Sleeve-ring oil bearings are used extensively in fans. Some sleeve-ring bearings may be water-cooled. Water-cooled sleeve bearings are used when hot gases are being moved by the fan. Heat is conducted through the shaft and into the oil which must be cooled to prevent overheating of the bearing.
| |
| | |
| Since lower-speed fans have bearings in hard-to-reach spots, grease-packed anti-friction bearings are used.
| |
| | |
| ===Fan dampers and Vanes===
| |
| | |
| Fan dampers are used to control gas flow into and out of the centrifugal fan. They may be installed on the inlet side or on the outlet side of the fan, or both. Dampers on the outlet side impose a flow resistance that is used to control gas flow. Dampers on the inlet side (inlet vanes) are designed to control gas flow by changing the amount of gas or air admitted to the fan inlet.
| |
| | |
| Inlet dampers (Inlet vanes) reduce fan energy usage due to their ability to affect the airflow pattern into the fan.<ref name=EPA/>
| |
| | |
| ===Fan ribs===
| |
| [[Image:CentrifugalFanBlades.png|thumb|right|325px|<center>Figure 3: Centrifugal fan blades</center>]]
| |
| | |
| The fan wheel consists of a hub on which a number of fan blades are attached. The fan blades on the hub can be arranged in three different ways: forward-curved, backward-curved or radial.<ref name=EPA/>
| |
| | |
| ====Forward-curved blade====
| |
| Forward-curved blades, as in Figure 3(a), curve in the direction of the fan wheel's rotation. These are especially sensitive to particulates. Forward-curved blades are for high flow, low pressure applications. A characteristic of forward curved blower wheels is their weight, due to the large number of blades they require. {{Citation needed|date=July 2011}}
| |
| | |
| ====Backward-curved blades====
| |
| | |
| Backward-curved blades, as in Figure 3(b), curve against the direction of the fan wheel's rotation. Smaller blowers may have '''backward-inclined''' blades, which are straight, not curved. Larger backward-inclined/-curved blowers have blades whose backward curvatures mimic that of an airfoil cross section, but both designs provide good operating efficiency with relatively economical construction techniques. These types of blowers are designed to handle gas streams with low to moderate particulate loadings {{Citation needed|date=July 2011}}. They can be easily fitted with wear protection but certain blade curvatures can be prone to solids build-up.{{Citation needed|date=July 2011}}. Backward curved wheels are often lighter than corresponding forward-curved equivalents, as they don't require so many blades.
| |
| | |
| Backward curved fans can have a high range of specific speeds but are most often used for medium specific speed applications—high pressure, medium flow applications.{{Citation needed|date=July 2011}}
| |
| | |
| Backward-curved fans are much more energy efficient than radial blade fans and so, for high power applications may be a suitable alternative to the lower cost radial bladed fan.{{Citation needed|date=July 2011}}
| |
| | |
| Also, some backward curved fans can also operate in reverse - the wheel rotates in the opposite direction, forcing air backward through the housing. {{citation needed|date=September 2013}} Also available are '''plug fans, '''which are centrifugal fans, most often backward curved, without scroll housings, and '''in-line''' centrifugal blowers, in which the duct for the fan contains the wheel, but in a way that allows air to exit the fan in exactly the same direction as it enters, which was previously achievable only with axial fans. {{citation needed|date=September 2013}}
| |
| | |
| ====Straight radial blades====
| |
| | |
| Radial blowers, as in Figure 3(c), have wheels whose blades extend straight out from the center of the hub. Radial bladed wheels are often used on particulate-laden gas streams because they are the least sensitive to solid build-up on the blades, but they are often characterized by greater noise output. High speeds, low volumes, and high pressures are common with radial blowers{{Citation needed|date=July 2011}}, and are often used in [[vacuum cleaner]]s, pneumatic material conveying systems, and similar processes.
| |
| | |
| ==Principle of Working==
| |
| | |
| The centrifugal fan uses the centrifugal power generated from the rotation of impellers to increase the pressure of air/gases. When the impellers rotate, the gas near the impellers is thrown-off from the impellers due to the centrifugal force and then moves into the fan casing. As a result the gas pressure in the fan casing is increased. The gas is then guided to the exit via outlet ducts. After the gas is thrown-off, the gas pressure in the middle region of the impellers decreases. The gas from the impeller eye rushes in to normalize this pressure. This cycle repeats and therefore the gas can be continuously transferred.
| |
| | |
| {|border=1px align=right
| |
| |+Table 1
| |
| |colspan="3" style="background:#7da7d9; color:white;" align="center"|Differences between fans and blowers
| |
| |-
| |
| !Equipment!!Pressure Ratio!!Pressure rise (mm Hg)
| |
| |-
| |
| |Fans||Up to 1.1||1136
| |
| |-
| |
| |Blowers||1.1 to 1.2||1136-2066
| |
| |}
| |
| | |
| ===Velocity Triangle===
| |
| [[Velocity]] triangle helps us in determining the flow geometry at the entry and exit of a blade. A minimum number of data are required to draw a velocity triangle at a point on blade. Some component of velocity varies at different point on the blade due to changes in the direction of flow. Hence an infinite number of velocity triangles are possible for a given blade. In order to describe the flow using only two velocity triangles we define mean values of velocity and their direction. Velocity triangle of any turbo machine has three components as shown:
| |
| [[File:Velocity Triangle for Forward Facing Blade.png|thumb|Velocity triangle for forward facing blade]]
| |
| *U - Blade velocity
| |
| *V<sub>r</sub> – Relative Velocity
| |
| *V - Absolute velocity
| |
| These velocities are related by the triangle law of vector addition: -
| |
| *V=U+V<sub>r</sub>
| |
| This relatively simple equation is used frequently while drawing the velocity diagram. The velocity diagram for the forward, backward face blades shown are drawn using this law. The angle α is the angle made by the absolute velocity with the axial direction and angle β is the angle made by blade with respect to axial direction.
| |
| [[File:Velocity Triangle Backward Facing.png|thumb|Velocity triangle for backward Facing blade]]
| |
| | |
| ===Difference between fans and blowers===
| |
| The property that distinguishes a centrifugal fan from a blower is the pressure ratio it can achieve. A blower in general can produce higher pressure ratio. As per [[American Society of Mechanical Engineers]] (ASME) the specific ratio - the ratio of the discharge pressure over the suction pressure – is used for defining the fans and blowers (refer Table 1).
| |
| | |
| ==Centrifugal fan ratings==
| |
| Ratings found in centrifugal fan performance tables and curves are based on standard air [[SCFM]]. Fan manufacturers define standard air as clean, dry air with a [[density]] of 0.075 pounds mass per cubic foot (1.2 kg/m³), with the [[barometric pressure]] at sea level of 29.92 inches of mercury (101.325 kPa) and a [[temperature]] of 70 °F (21 °C). Selecting a centrifugal fan to operate at conditions other than standard air requires adjustment to both static pressure and [[Electric power|power]].
| |
| | |
| At higher-than-standard elevation ([[sea level]]) and higher-than-standard temperature, air density is lower than standard density. Air density corrections need to be taken into account for centrifugal fans that are specified for continuous operation at higher temperatures. The centrifugal fan will displace a constant volume of air in a given system regardless of the air density.
| |
| | |
| When a centrifugal fan is specified for a given CFM and static pressure at conditions other than standard, an air density correction factor must be applied to select the proper size fan to meet the new condition. Since {{convert|200|°F|°C|abbr=on}} air weighs only 80% of {{convert|70|°F|°C|abbr=on}} air, the centrifugal fan will create less pressure and require less power. To get the actual pressure required at {{convert|200|°F|°C|abbr=on}}, the designer would have to multiply the pressure at standard conditions by an air density correction factor of 1.25 (i.e., 1.0/0.8) to get the system to operate correctly. To get the actual power at {{convert|200|°F|°C|abbr=on}}, the designer would have to divide the power at standard conditions by the air density correction factor.
| |
| | |
| ==Air Movement and Control Association (AMCA)==
| |
| | |
| The centrifugal fan performance tables provide the fan RPM and power requirements for the given CFM and static pressure at standard air density. When the centrifugal fan performance is not at standard conditions, the performance must be converted to standard conditions before entering the performance tables. Centrifugal fans rated by the [[Air Movement and Control Association]] (AMCA) are tested in laboratories with test setups that simulate installations that are typical for that type of fan. Usually they are tested and rated as one of four standard installation types as designated in AMCA Standard 210.<ref>ANSI/AMCA Standard 210-99, "Laboratory Methods Of Testing Fans for Aerodynamic Performance Rating"</ref>
| |
| | |
| AMCA Standard 210 defines uniform methods for conducting laboratory tests on housed fans to determine airflow rate, pressure, power and efficiency, at a given speed of rotation. The purpose of AMCA Standard 210 is to define exact procedures and conditions of fan testing so that ratings provided by various manufacturers are on the same basis and may be compared. For this reason, fans must be rated in SCFM.
| |
| | |
| ==Losses in Centrifugal Fan==
| |
| In centrifugal fans losses will be there in both stationary and moving parts of the centrifugal fan stage. We can get the actual performance of the centrifugal fan by taking these stage losses into account.
| |
| Various types of losses
| |
| | |
| === Impeller entry losses ===
| |
| Due to the flow at the eye and it’s turning from axial to radial direction causes losses at the entry. Friction and separation causes impeller blade losses since there is change in incidence. Normally these impeller blade losses are also included in this head.
| |
| | |
| === Leakage loss ===
| |
| Leakage of some air and disturbance in the main flow field is caused due to the clearance provided between the rotating periphery of the impeller and the casing at the entry.
| |
| | |
| === Impeller losses ===
| |
| Passage friction and separation causes impeller losses which are dependent on relative velocity, rate of diffusion and blade geometry.
| |
| | |
| Impeller balancing is done by small weights on a balancing machine. All energy of vibration is lost (''i.e.'', can easily amount to %50 air-flow loss in home AC units).
| |
| | |
| === Diffuser and volute losses ===
| |
| [[Friction]] and [[separation process|separation]] also causes losses in [[diffuser]]{{disambiguation needed|date=September 2013}}. Further losses due to incidence occur if the device is working in off-design conditions. Flow from impeller or diffuser expands in the volute which is having larger cross section leading to the formation of [[Eddy]], which in turn reduces head. Friction and flow separation losses also occur due the volute passage.
| |
| | |
| === Disc Friction ===
| |
| Viscous [[drag (physics)|drag]] on the back surface of the impeller disc causes Disc friction.
| |
| | |
| ==See also==
| |
| {{Commons category|Centrifugal fans}}
| |
| *[[Mechanical fan]]
| |
| *[[Ducted fan]]
| |
| *[[Standard temperature and pressure]]
| |
| *[[Wind turbine]]
| |
| * [[Three dimensional losses and correlation in turbomachinery]]
| |
| * [[Waddle fan]]
| |
| | |
| ==References==
| |
| {{reflist}}
| |
| | |
| [[Category:Chemical engineering]]
| |
| [[Category:Compressors]]
| |
| [[Category:Turbomachinery]]
| |
| [[Category:Turbines]]
| |
| [[Category:Thermodynamics]]
| |
| [[Category:Fluid dynamics]]
| |
| [[Category:Aerodynamics]]
| |
| [[Category:Fans]]
| |
| [[Category:Russian inventions]]
| |